Question about NetGear Computers & Internet

4 Answers

Belkin f9k1106v1 range extender not connecting

Not able to connect to router. default address not working for initial set up

Posted by Anonymous on

Ad

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Expert
  • 18 Answers

If you have to face a problem with Belkin range extender Which troubles you in terms of Connectivity and Connection

1 Restart Your Modem First then Restart your Router And Extender
2 Please Your Extender Within 30-35 Yards Of Your Main Wireless Router.
3 Make Sure All Lights Are Blinking On Router And You Have the Internet to your Router

For more details kindly visit
Belkin Range Extender Won Connect to Internet Belkin Range

Posted on Aug 25, 2018

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • NetGear Master
  • 317 Answers

Hi , I was also facing same problems.I have solutions please follow some steps:

1.Restart Your Main Wireless Router And Modem.
2.Now Turn Off Your Belkin Range Extender And Wait For 20 seconds (unplug From Power)
3.Please Plug Your Extender Back To Power Outlet And Restart Your Computer.

Still Having Problems?
Don't Worry Visit here for more solutions:
Belkin Range Extender Won Connect to Wireless Router TechVaidya

Posted on Aug 11, 2018

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 3 Answers

    1. Plug the Belkin range extender into a power outlet.Keep in mind that your range extender must be placed in the signal of your wifi network.
    2. Use your mobile device or computer to browse the available networks and select Belkin.setup from the list.
    for more details visit
https://bit.ly/2ZnBOzb

Posted on Aug 30, 2019

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • NetGear Expert
  • 162 Answers

The steps of setting Belkin range extender is the simplest one.
step 1 plug the router to the power outlet and place the extender near to the router or in the range of the router.
step 2 check your computer or phone available network list.
step 3 there is a unsecured network by name of Belkin.setup available.
for more steps visit https://belkinrangesetup-extender.com/

Posted on Jul 09, 2019

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 132 Answers

SOURCE: Opening the NAT connection for Xbox 360 working through 2 routers

  1. How do you connect your Linksys router to Belkin router? Do you connect your Linksys router to the Internet/WAN port of the Belkin?
  2. If so, what is the Internet connection type set in your Belkin router? Is it dynamic?
  3. If the Belkin router is set to dynamic IP and if it is obtaining an IP address from your Linksys router(you may check the status page of your Belkin router and look for IP address), then you may need to forward or set that IP address as the DMZ to your Linksys router. Make sure that XBOX is still configured as the DMZ host in your Belkin
Hope this helps!

Posted on Nov 17, 2008

  • 19 Answers

SOURCE: How do I access my Belkin N Router's settings?

open internet explorer and type 192.168.2.1 and the will get u to the belkin router page and then click on mac address control and then type ur password to get in to the router and it will take u to all the mac address u have allowed or denyed

Posted on Dec 28, 2008

SOURCE: Wireless connection keeps dropping after about a day.

I had the same problem (see Jan 09) but I found the solution:
I had trouble with the router resetting from time to time, that was fixed by upgrading to firmware 1.05. But I still had the wireless problem.
For me, disabling 'UPnP' (advanced->advanced network) and disabling turbo G mode (setup->wireless setting) did the trick.
Work great since then, both my laptop and my media center stays connected, going on one month now.
Hope it can helps other.

Posted on Feb 17, 2009

  • 1 Answer

SOURCE: Belkin Wireless N router/Embarq 660 modem/No internet

THE PROBLEM IS THAT THE BELKIN RTR AND THE 660 HAVE THE SAME IP ADDRESS THE QUICKEST FIX IS TO RENAME THE LAN IP ADDRESS OF THE BELKIN RTR

Posted on Jun 12, 2009

  • 1 Answer

SOURCE: Belkin F5D8233 keeps dropping connection

change your wireless mode to either 802.11g or 802.11.n, do not use 802.11b&802.11g&802.11n option.

Posted on Nov 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Risricky@ai cannot install my linksys router onto my laptop


I presume you mean that you cannot connect to your linksys router from your laptop and have not used it before.
You should make the initial connection using a network cable rather than wireless. Once you have done this you will be able to connect to the linksys router administration webpage by opening internet explorer (other web browsers are available) and typing in http://ipaddress where ip address is the default ip address as specified in the router getting started or installation guide. The default for Linksys routers is http://192.168.1.1 Once you can access the Administration page you should be able to configure the wireless settings using the inbuilt wizards.

Hope you get sorted
Caltor

Sep 07, 2011 | Computers & Internet

2 Answers

How can I reset the password for my D Link 601 router? I connected to it with a different laptop and it seems to have set its own password. We can't connect any new stuff (Nook, iTouch, etc.).


plug the cord of the router and press the small button with a paper clip or anything that can insert to the hole of a reset button.. press it for 5-10sec then access your router on the address bar with their corresponding router's IP address..
hope it help.

Sep 07, 2011 | Computers & Internet

1 Answer

Trying to connect to wireless router


Hi,

Welcome to Fixya. If you want to connect you Wii to the internet wirelessly first we need to know the settings of your router. Listed below are the steps on how to access your router. You need a working computer connected to the router to access it follwed by the steps on how to connect our Wii.

How to access the Router:

1. You need to know the ipaddress of your router. You can refer to the manual or check the Default Gateway of your computer (Make sure that you connect the computer to the router using an ethernet cable for you to get the Default Gateway). Click on START then RUN. Type CMD on the small box on the lower left of the screen. Type IPCONFIG on the black window and get the value of your DEFAULT GATEWAY (it starts with 192.168.x.x)

2. Open a Browser, Type the DEFAULT GATEWAY on the address bar of your Browser. It will ask you for a username and password. (Refer to the manual of your router or post a reply so that i can provide you the username and password of your router)

3. Go to the Wireless Settings Page of your router. Look for the SSID or the Network Name and the Network Key or Passphrase. You can personalize it so that you can easily remember the details.

4. Make sure you connect to your SSID and enter the Network Key to make it secure.

Now that we have the information needed lets connect your Wii to the internet.

1. Select Wii Settings
2. Then Internet then Connection Settings
3. Search for an AP or SSID
4. Input Security Key or Network Key
5. Test the Connection.
Other Suggestion

Did this connection used to work but has suddenly stopped? "Power cycle" your router by unplugging it from the power outlet. Wait a few minutes, and plug the modem back in. Wait a couple of minutes for the modem to initialize, then plug in the router. Try to connect the Wii and test for proper response.

The Wii may have detected and set itself to the wrong security type during the initial connection set up. Try creating a new connection file and going through the connection process again but be sure that when the Wii asks for a security code, the type shown on screen (WEP or WPA) is what your router is set to. If it is different

Change your router's channel setting to 1 or 11. By default, most routers broadcast on channel 6, which overlaps with other channels and may be weaker.

Thanks for using Fixya.

Jun 04, 2011 | Nintendo Wii Console

3 Answers

192.168.0.1. don't work


linkssy is not 192.168.0.1 it is 192.168.1.1 try that

Jan 02, 2011 | Linksys Wireless-G Broadband Router

1 Answer

I purchased a wre54g range expander and have tried everything but it doesnt work


Who is the manufacturer of your wireless router?
check the IP address of your router.
connect the computer to the router and check the Ip address of the computer and the default gateway number. Default gateway is the IP address of your router. suppose the default gateway is 192.168.1.1. then open the set up page of the router . check the wireless settings of the router SSID ,channel and the security settings. Do not change the settings on the router.
If you are using WPA2 security settings them that will network on the WRE54G.
Now your range expander and the router IP addresses should be in the same range. Suppose you router IP address is 192.168.x.y and the IP address of the WRE54G is by default 192.168.1.240.
Now the x in the router IP address should be 1.
If it is, then connect the WRE to the router and open the set up page of WRE. change the wireless settigns on the WRE and power cycle the WRE and the router.
It should work
For more info about networking Click Here

Oct 06, 2009 | Linksys : WRE54G Wireless Range Extender...

1 Answer

If a change in my firewall is preventing netgear router, i do i fix?


First, make sure the cables are properly connected, if using xDSL modem, it must be connected to the WAN port, the pc on the ethernet ports (any of the 4 ports available).
Second, check your current IP Address (default 192.168.1.x), then ping from your pc the ip address of the router (default 192.168.1.1). If OK, then your LAN connection works fine.
Third, ping any internet site, i.e. ping www.yahoo.com. if a reply response is received, your internet connection is now working.

If not, reset the router then do the initial set up from the router web page. Go to IE or mozilla browser, type http://192.168.1.1 (default ip add of router), the password or username is admin (default - refer to your manual). If already inside the page, go to the setup folder then proceed to configure the router. After all the configuration, check your internet connection, go to any web site.

Sep 15, 2009 | NetGear WGR614 Wireless Router

3 Answers

No connection between modem-router-pc


Linksys reset
The easiest method of resetting your Linksys router’s password is to reset your router back to the default factory settings. This is done by simply holding down the reset button located on the back of the unit for at least 30 seconds. Once the router has been reset, it must be reconfigured. Using your web browser go to URL address http://192.168.1.1. You will then be prompted to login to your router. A log-in screen asking for the password will automatically appear. At this time enter the default password “admin”, in lower case letters into the password field. The username field may be left blank at this time. (Note: both the default username and default password are set to “admin” on some of the newer Linksys router models).
Router setup
Shutdown your PC. Unplug the power from the router and the cable modem.
Wait 30 sec. then plug in the power to the cable modem, wait 30 sec. then plug the power to the router. Wait till you have "Internet" light then restart your PC. The PC should pick up an IP address and you should be able to get on-line. This is if you have a cable service provider. If you have DSL, the router needs to be configured with PPPOe.



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Aug 13, 2009 | Linksys Wireless-G WRT54GS Router...

1 Answer

Cannot connect to remote Microsoft VPN


Hello, some ISPs require someone to manually/staticly assign a default gateway for a router. With computer connected directly to ISP modem, if using Win XP click start, run and enter "cmd". This will bring up a black text box(CLI). at the prompt> enter ipconfig and click enter. This will show the computers IP address Subnet mask and default gateway. You will need to connect the modem to router to computer. If you haven't changed default settings, From browser enter 192.168.1.1 in window. Enter. This will open router settings. Username and password will be "admin". It may require admin for either or both. You may have a Initial set up link. From here you'll need to enter Default gateway address to access the modem and internet. Hope this helps

Mar 19, 2008 | D-Link DSL-G604T Wireless Router

1 Answer

Unable to get connected to Belkin f5d6130 AP


Hi,

You need to be connected using  wired Ethernet (PC's LAN card to Router's Ethernet Port (at the back)).  This is the preferable INITIAL way to configure the router before going wireless. Also it would be to your advantage to initially set your PC (that will be used for configuring the router)  to "Specify an IP address" (static settings) and not "Obtain an IP address automatically."

For a PC connected via UTP networking cable attached to a Belkin F5D6130 AP, the networking settings could be:
IP Address 192.168.2.2
Subnet Mask 255.255.255.0
Default Gateway 19*2.168.2.1
DNS Server 192.168.2.1
Reboot

Post back results. Good luck and kind regards.

Oct 12, 2007 | Belkin (F5D6130) 802.11b Wireless Access...

2 Answers

Cant accses router


Pressing and holding the reset button on the router for about 5 seconds should reset the router, but you may need to connect with the router via an RJ45 network cable incase the wireless is not able to set it up The default ip address of the router should then be 192.168.2.1. do not use the windows repair wizard as this totally messes up your pcs ip address, make sure that your network wireless and wired adapters, are set to obtain an ip address automatically You shouldnt change the PPOE or PPOA settings, as they are the settings on which your ISP allows your router to connect to the server. Manually entering an ip address will effect the address of the router so keep the settings as enable DHCP to assign ip addresses automatically. Ensure when you have it running you save the settings so as you can reinstall them if neccasary.

Aug 20, 2007 | Belkin (F5D7231-4) Wireless Router

Not finding what you are looking for?

Open Questions:

Computers & Internet Logo

Related Topics:

1,166 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...