Removing the arm bar from the graco trekko

Instructions

1. • 1 Determine the amount of links that need to be removed for the watch to fit on your arm correctly.
     
   • 2 Find the tiny holes on each link. Most DKNY link wristwatches, such as the 3107 model, have holes at the links near the clasp.
     
   • 3 Using the screwdriver, gently push the pin holding the link bar on the first link you want to remove. The link bar should come out on the other side.
     
   • 4 Take the pliers and completely remove the link bar from the band. The link band will still be attached to the clasp. Remove the link with the pliers. Repeat Steps 1 through 4 for each additional link you want to remove.
     
   • 5 Gather the watch band and and bring the two sides back together. Join the link bar and the clasp together and, using the screwdriver, press the link bar back into the hole completely.
     

How to Take the Links off DKNY Watch eHow

You need to loosen the torsion bar adjusting bolts until all the tension is removed, remember to mark a reference point from bar to frame so you can get close to the correct riding height after reassembly. Can't tell if you split the ball joint from the knuckle from your explanation but a couple of good solid whacks to the lower knuckle will unlock it. Mark & remove the control arm bushing bolts and use a pry bar to push out arm @ bushings.

Hi Kaylee

We would recommend you contact Graco for assistance.

Contact Graco

I am assuming you have lubed the wheel with a silicone based spray lube.
Is it wobbling with the wheel in the locked position? Th only reason a wheel can wobble is if the axle and the actual wheel have too much play. A thin shim washer may tighten the axle to wheel spacing. Most hardwar stores will have thin washers. Give it a try. Your manual made no reference to wheel maintanance so if you purchased it new I would call Graco and complain. If used, try to eliminate the problem. If you need it here is your manual.
Graco Trekko Manual

I also need to replace three wheels as they have rusted really bad any luck anyone on where you can get parts for a Graco Trekko three wheel stroller

first jack up side you will be working on and place jjackstand under the frame, next remove the wheel,to make it easier remove the caliper and tie away, dont remove the brake hose!, then remove the rotor it slides off you may need to tap backside with a hammer, next is to remove the bolt and nut from the lower balljoint, then use balljiont tool to saperate the lower control arm from spindle, you may need a pry bar to pull down on control arm to completly separte move spindle to side and let arm up, next remove the axle (cv) nut on the front, then use pry bar to pop out of trany, install new axle hold straight and slide into tray as far as you can then with nut on the axle a little tap to axle in to trany the rest of the way you will feel it go in and lock and then reverse direction to put back together, hope this helps.

(Caution ) sway bar end is under pressure.

1.go to AutoZone get new linkage bars or just the bushings depends on wether the bar has grooves wore into them from use and new nuts. 2. Raise and safely support vehicle,3. remove tire, 4.using floor jack safely support the lower suspension arm and raise to remove pressure on the linkage bar between swaybar end and lower arm 5. remove the nut under the lower suspension arm that retains the swaybar linkage ,6. loosen and remove nut at swaybar end. 7.at this time only lower the lower suspension arm enough to remove the linkage bar. install new bushings or bar to the swaybar end don't completely tighten nut at this time.8. install new lower bushing then jack the lower suspension arm back up aligning the lower end of the linkage with the hole in the arm once pressure is lifting the swaybar install the lower nut and tighten at this time Torque top nut to35-47 Ft lb and bottom nut 8-10- Ft lb lower the jack from under the lower arm and install tire lower vehicle ready to go Appx 1 Hr per side

First, you would have to remove any secondary pieces like bassinet, mobile, change table, mattress, etc.

Next, pull up on both sets of long side bars...and do the same with the two short side bars.

If you have done this correctly, the play pen becomes a cylindrical set of poles that can be stored in the Graco carrying bag.

I think it is on the right side if you are facing the stroller, underneath there is a small button you push and the bad will swivel. I think the button is black so you might have to look closely.

If this is for the Graco Snugride (I have the Windsor model from the Quattro Travel System), this will work:


1. Push the Graco canopy to one side, exposing the plastic support bars that hold the canopy in place.

2. The center of the support is where the canopy comes apart. Using both hands, pull the canopy support
bar apart (as if you were playing tug-of-war). It's best to grab the curved ends and pull HARD (and point it away to the side so that you don't hit your face).

3. Once the support bars are apart, remove the old Graco canopy and slip on the new/freshly washed canopy.

4. Secure the support bars by snapping them shut, and then slide the canopy into place.