Wiring cat 5 jack

Standard phone wiring is blue/blue white for your T/R.

Here's the wiring instructions: http://www.leviton.com/OA_HTML/ibcGetAttachment.jsp?cItemId=nNBKTVaZ2nU2mhkps672vw&label=IBE&appName=IBE&LEVCOMP_pses=ZGFA29E0DBC9686AA1D14C9C2AA2763721F62C7F83E969AD4822D897CE157A46A78B7EB01F8BC392D4241779B1759B01270DF9EBAAD8B4427C&minisite=10251

Countdown timers are made to work with bath fans.
Leviton countdown timers are stout product with 1HP rating.
http://waterheatertimer.org/Countdown-timer-horsepower-ratings.html#6200

It sounds like timer is bad.
Wiring sounds good. Make sure you don't have Load and Line wires reversed. Try reversing Load-Line wires and see what happens.
Another thing that affects electronic timers is line noise/interference. If replacement timer does same thing, then noise is suspect. Try timer on another circuit without fan. Try another brand timer. Update to newer LTB60 Leviton timer. Use cheap circuit tester from home center to check outlet on same circuit.

how i can punch cat 5 cable in cat 5 io box

I haven't used Panduit specifically, but on almost every jack (leviton, on Q, ortronics) it actually shows the color codes on the side or bottom of the jack. They are usually marked for both A and B, so make sure you go by the color code marked A. Strip your cat 5, use an impact tool to punch the colored wires into the corresponding slots on the jack.

http://www.leviton.com/OA_HTML/ibeCCtpItmDspRte.jsp?item=4044§ion=10103&minisite=10025
The Leviton page for Leviton 5613 does not have a troubleshoot.
Manual shows simple wiring diagram.
3-way switches will not operate lights if switches are wired incorrectly.
Check your ground wire is connected.
Leviton 5613 series is illuminated.
Check that both switches have 5613 number.
Swap switches and see if problem is inside switch.

Click on this site for CAT6 wiring diagrams :-
Normal 0 http://www.google.com.au/images?hl=en&q=cat6+wiring+diagram&um=1&ie=UTF-8&source=univ&ei=ANu7TMz1PMTQcbzFiPwM&sa=X&oi=image_result_group&ct=title&resnum=1&ved=0CCwQsAQwAA&biw=1010&bih=473

http://www.leviton.com/OA_HTML/ibcGetAttachment.jsp?cItemId=y8QWKImQP7cPVn3GRND9ig&label=IBE&appName=IBE

Hi tonybenjamin

Here are the pinouts for a regular fly lead (PC to Switch"hub") and for a cross over cable (PC to PC)
Front view of the RJ45 MALE pin. Pin's top with Locking clip
1. Fly Lead

Name Pin Wire Color Pin Name TX+ 1 White/Orange 1 TX+ TX- 2 Orange 2 TX- RX+ 3 White/Green 3 RX+ 4 Blue 4 5 White/Blue 5 RX- 6 Green 6 RX- 7 White/Brown 7 8 Brown 8
2. Cross Over

Name Pin Pin Name TX+ 1 3 RX+ TX- 2 6 RX- RX+ 3 1 TX+ RX- 6 2 TX- Extra Pins 4 4 Optionl Pins
(connected straight
to same pins) 5 5 7 7 8 8

Regards
Go-Tech

Hi,

wiring can be done in only two ways (standard)

if the jack is being connected with the switch you have to follow the below given color code.

1st orangewhite
orange
greenwhite
blue
blue white
green
brownwhite
bown

if you need to connect two same type of devices swap 1 st with 3rd and 2nd with sixth ( color code)