Driver needed I lost my disc and need a driver for downloading off of internet can you please guide me? Sabrent 1 Ft USB 2.0 to Serial DB9 Male RS-232 Cable Adapter

The Insignia NS-PU99501 USB to serial (RS-232) converter cable should be a plug and play item with Windows 7 and 8. This assumes an active internet connection and Windows Update is set to search for drivers for new devices. See https://www.insigniaproducts.com/pdp/NS-PU99501/5883029 and go to the Support & Downloads tab to find the manual and the driver for a Macintosh OS.

The Prolific chipset in this Insignia device is the PL2303. For other Windows versions, try http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41 for the driver.

I hope this helps. You may need to check the chipset suffix with the tool on the above Prolific support site.

Cindy Wells

Try to install drivers from disc.

How about someting like this http://www.google.com/search?q=Cblwhl+USB+to+Serial+Cable+Type+A+Male+to+DB9%2FDB25+Male+&hl=en&tbs=shop%3A1&aq=f

Please download http://www.sabrent.com/drivers/USB-AVCPT-New.zip to a location you can easily find later (DESKTOP is a good location so you can delete the folder after installation)

At this point you can update the drivers manually...
1. Right-Click on MY COMPUTER, Select PROPERTIES.
2. Select HARDWARE
3. Select DEVICE MANAGER
4. Scroll down to the USB Video adapter.
5. Right Click on the Device and select UPDATE DRIVER.
6. Do NOT allow Windows to automatically find the drivers.
7. BROWSE to the Folder you created at the beginning and direct it to the correct folder for your operating system. STK1150 should appear.

Follow this link and choose Serial ATA from the dropdown list.
Then choose SA-IDE88 and the driver download will start.

http://www.sabrent.com/#section=Drivers&itemName=&itemID=0

Are you tring to run a parallel printer from a serial port? If so then it will not work at all. You would need a serial to prallel adaptor that also has the software drivers needed to convert the signal.

Sounds like you need to install drivers.
Tell me the manufacturer and model number of the foot pedal. I'll track down a driver for it.

Try searching the following page
http://www.sabrent.com/#itemName=&itemID=0&section=Drivers

If you have a BackUPS CS, you are probably either using it with the USB cable that is supplied or with the 940-0128A supplied by APC, which permits running the UPS in dumb mode. By building your own cable, you can now run the BackUPS CS models (and perhaps also the ES models) using smart signalling and have all the same information that is available as running it in USB mode.
The jack in the UPS may be easily use a 8 pin RJ45 connector. It is easy to construct the cable by cutting off one end of a standard RJ45-8 ethernet cable and wiring the other end (three wires) into a standard DB9F female serial port connector.
PC Signal PC pin UPS Pin UPS signal RxD 2 2 TxD TxD 3 8 RxD GND 5 7 Ground FG Shield 4 Frame Ground Though these UPSes are USB UPSes, APC supplies a serial cable (typically with a green DB9 F connector) that has 940-0128A stamped into one side of the plastic serial port connector.
Here is suggested scheme of original 940-0128A cable
APC Part# - 940-0128A computer --------- Inside the Connector--------- UPS DB9-F | | RJ45 pin - signal | | Pin - Color | | 4 DSR ->|---+ | | | diode resistor | 6 DTR ->|---+---->|----///---o kill power | 8 Orange | | 1 DCD <-|----+ | | | | 2 RxD <-|----+----------------+--o low battery| 3 Brown | | | 7 RTS ->|----------+--///--+ | | | | | +--///--+ | | | | 8 RI <-|----+----------------+--o on battery | 2 Black | | | 9 CTS <-|----+ | | signal | 5 GND --|-----------------------o ground | 7 Red | | 3 TxD | | | chassis | Chassis/GND |-----------------------o ground | 4 Black | | | Not connected | 1, 5, 6, 9, 10 --------------------------------------

Please provide more information. OS, what exactly happens, do the drivers show up in the device manager? Do you have local admin rights?