Omron pulse massager HV-F126 not working

hi,

have one.
if its on batteries make sure they are new and if they are check battery terminals use an emery board or sandpaper to clean the battery terminals or you have to use the exact right power supply also with at least an 1 amp output. use the right power supply.

found this on page 21 Monitor did not detect pulse rate Remove the arm cuff. Refer to "Applying the arm cuff" on page 13. Wait 2-3 minutes. Take another measurement
http://www.quickmedical.com/downloads/omron-hem780n.pdf

If you are using a remote then you would set the machine in standard for controlling output and also to AC output, HF tig, contactor and control in remote position. I don't know if this helps or not but I pulled it from an owners manual.

1/16" (.062) - pre-flow .1 sec., hot start 20, amperage 70, Hz 100, balance 20%, post-flow 6.0 sec.

For pulse settings - set pulse width 60%, peak current 100, background current 30, Hz 1.0

1/8" (.125) - pre-flow .1 sec., hot start 20, amperage 150, Hz 80, balance 20%, post-flow 6.0 sec.

For pulse settings - set pulse width 60%, peak current 150, background current 50, Hz 1.0

3/16"-1/4" - pre-flow .1 sec., hot start 20, amperage 185, Hz 60, balance 20%, post-flow 8.0 sec.
For pulse settings - set pulse width 60%, peak current 185, Background current 125, Hz 1.0

check your fuses something could be bad.i would replace the battery.if that dont work ask a auto repair shop.

Jeanie Rub Service Information Jeanie Rub Warranty Information
Core Products provides a full one-year warranty on all defects in material and workmanship. Any misuse, unauthorized repairs, or product abuses are excluded.

Defective products reported within one year of date of purchase will be replaced or repaired. Call the Customer Service department at Core Products at 800-338-7014 for a return authorization number and to arrange shipping.
Out-of-Warranty Service

Core Products will repair most Jeanie Rub Massagers after the warranty has expired. Some of the very early models can not be repaired but can be returned for a $50.00 credit towards a new unit.

It is difficult to determine the extent of the repair until the unit is inspected however, we guarantee the service call will not exceed $89.00 plus shipping.

Basic Service Package - $49.00 + $13.00 Shipping
- Cleaning
- Replace worn parts & pad

Complete Service Package - $89.00 + $13.00 Shipping
- Cleaning
- Replace worn parts & pad
- Replace motor

Cord Replacement - $25.00 + $13.00 Shipping
- Replace worn cord

You can find Omron HV-F123 manual at http://www.omronhealthcare.com/service-and-support/product-support-and-solutions/.

Hello -

I do not find a manual for the HV-F176 Omron Elepuls low-frequency massager on either the Omron Healthcare United States web site,
https://omronhealthcare.com/
or on the Omron Healthcare international website,
https://www.omron-healthcare.com/en/products/painmanagement

Therefore, if you reside in the USA, I suggest you contact Omron Healthcare customer service and ask about the availability of the user manual for model HV-F176. There may be a copy of the manual of the discontinued massager in the company Archives. If so, there may be a charge for a copy,

See the Contact Us (USA) information here:
https://omronhealthcare.com/contact-us/
There you will find a toll free (USA) phone number as well as a form to complete to send an email message.

Best wishes.

Hi library336

The Omron HEM-780 generally has 5 Error Messages:


1]
ERROR MESSAGE: A single (E) Error message indicates movement during the measurement process, resulting in an inconclusive reading or the absence of a Blood Pressure or Pulse reading caused by a weak Arterial Pulse.

SOLUTION: Remove the cuff. Wait 10-15 minutes. Repeat measurement using approximately 40mmHg more pressure than in the previous measurement.

2]
ERROR MESSAGE: A Double (EE) Error message indicates an under-inflated cuff. Remove the cuff. Wait 2-3 minutes.

SOLUTION: Repeat measurement using approximately 40mmHg more pressure than in the previous, under-inflated measurement.

3]
ERROR MESSAGE: An E directly below another E Error message indicates an over-inflated cuff (in excess of 300 mmHg). Remove the cuff.

SOLUTION: Wait 2-3 minutes. Repeat measurement using approximately less pressure than in the previous, over-inflated measurement.


4]
ERROR: A Blank Screen indicates low or depleted batteries.

SOLUTION: Remove and replace all 4 AA Batteries. Do not mix used and new batteries.

5]
ERROR MESSAGE: An (Er) Error Message indicates an abnormal memory function caused by a faulty internal component.

SOLUTION: Call Omron Customer Service, Toll Free, on (in the USA) 1-800-634-4850 (or on the equivalent Toll Free or Freefone Number in your country).

I hope this helps.

If this Answer goes some way towards helping to resolve your Query, Problem or Fault, please take the time to Rate it.
Doing so helps Solution Providers, like me, better understand the needs and the point of view of Askers, like you, and guides us in exploring the best ways to provide the most comprehensive, useful and high quality Responses and Solutions we can.

If you need further help, please do not hesitate to post another Question or add a Comment to this Question.

Thanks for using FixYa.

Are you still having problems? [email protected]

the back massager with heat stopped working, bought a new power cord, still does not work, must be something in the back massager, but what to do ? ken