Leviton vzm10 blinks when turning on and lights do not come on

Contact Leviton direct. They will know if the fan or sensor is faulty or it is the control that is faulty?

https://www.leviton.com/en/products/residential/fan-controls/fan-speed-controls/humidity-sensor-fan-control

..

Leviton 6161 is shown on Leviton as 500 watt incandescent-only 4-level dimmer that cannot control a fan.
If this is a ceiling fan and light, then search for fan light dimmer, or fan control,

If this is bathroom fan-light installation, you are needing a countdown timer rated for both bulb and fan... which will require Neutral wire...
Different timer choices with manuals appear following link:
http://waterheatertimer.org/Countdown-timer-horsepower-ratings.html#Leviton

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

This site can give you the support (oper. man. and spec sheet) youi need to correct this problem.Electrical devices lighting controls network solutions Leviton com

Your product is not identified by number given.
Leviton posts manuals online by searching Leviton xxxx .pdf.
There is a CPT 602 lighting console
However no result shows online or at Leviton for a 602 dimmer
Contact Leviton:
http://www.leviton.com/OA_HTML/SectionDisplay.jsp?section=37579&minisite=10251
Add a comment and attach photo or video for possible identification

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Hi Leonard,

I'm a licensed electrician and will be happy to help you get this working again. I suspect an incorrectly wired or incompatible switch or a load that is not designed for dimming. To know which one(s) is the problem and to be able to provide a solution, I need a little more information.

1) What was the old switch brand and model number?
2) What is the new Leviton switch's model number?
3) What type of light bulbs are you trying to operate in the 3 fixtures?
4) What is the number of and wattage of each lamp in the fixtures?
5) How many switches operate the lights?
5a) If more than one switch is used, what is the brand and model number of the other switch(es)?

Thanks

You posted under Leviton 6124 timer.

I have tested this timer.

If timer worked correctly before and then started blinking, the timer might be bad.
Turn off power to timer and see if timer resets.

If this is new installation and lights are blinking on-off, then white and red wires are probably connected together.
Re-connect wires.
Open link below to read ez-wiring steps, and to access on-line manual.
http://waterheatertimer.org/Leviton-timers.html

Add a comment for more free help.
Also take advantage of fixya phone service.
For a price, expert speaks with you over phone while you work on timer or any do-it-yourself project.
Fixya is always less expensive than a service call.

Some switches are not designed to work with the florescent bulbs. It's a matter of them trying to push a starter for the light. Check the package and see if it's compatible.

The Leviton PR180 is a motion detector, or occupancy detector.
It senses infrared heat from a person's body.

I am looking at the manual from Leviton.

Maybe this will help:
There is a small adjustment screw under the wallplate where you can adjust light sensitivity.
Use fingernail or small screwdriver.
Turn control towards the "-" sign and lights will turn on in 'less lighting conditions'

I will be here for a few more hours.
Add a comment and I will help further is needed

one of the white wires has power on it constantly....that wire connects to the black wire of the leviton.......the other white wire which has no power to it is going to whatever needs power so that wire connects to the red wire of the leviton....the green wire connects to the metal box where your mounting the leviton.

is there another light in the vacinity or is the light in question itself pointed at the photocell. most likely scenarios are that the light is pointing at its own photocell so when it is off the photosell senses dark and turns it on but then when light comes on tricks photocell into thinking it is daylight,check position of photocell and adjust away from light source if problem persist could be ballast going bad