I want to change speed dial nos. don't have manual for instructio

There doesn't appear to be a way. Sometimes on multi-phone business systems, a technician can connect a laptop with dealer software and make changes or edits that a user can't.

If that particular number needs to be at Number 1, you would have to delete them all and reprogram them all again.

http://www.voicesonic.com/panasonic/manuals/KX-T76xx_User_Guides/KX-T7630_User_Guide.pdf

..

First, make sure you're in the manual exposure mode, not manual focus mode, as set by turning the mode dial to the "M" position.
In manual exposure mode, turning the main command dial should change the aperture, while turning the subcommand dial should change the shutter speed.
If the two command dials don't have the expected effect, reply to this post and we can troubleshoot further.

I was unable to locate a user manual for that particular device, however the basic instructions for programming speed dial functions are normally very similar between most phones.


Generally there are ONE TOUCH Speed Dial buttons labelled something like M1, M2, and M3 on the dial pad somewhere.


There should also be another button labelled PROG or STORE on the keypad as well.


Normally to program a number into a ONE TOUCH speed dial memory location you carry out the following procedure:


Lift the handset.


Then press the PROG (or STORE) button.


Now just use the number keypad to dial the full telephone number that you want to store in a Speed Dial location.


Once the full telephone number is dialed, then push the M1 button to store that phone number in the M1 One Touch Speed Dial location.


The phone may or may not show some kind of confirmation that the M1 location was just programmed, then just hang up the handset.


Now when you lift the handset and press the M1 button, the phone should automatically dial the phone number you programmed into it.


Now just repeat the same process for the M2 and M3 One Touch Speed Dial buttons with other phone numbers if necessary.


To change one of the Speed Dial numbers, just carry out the normal programming procedure for that location using the new phone number and the old number will simply be overwritten.


I truly hope that was helpful to you.
Good luck and take care.

Joe.

You may download the manual here.

You have neither a 7730 (the category you asked in) or a 7433 phone sytem. If your phone is really a 7433, you have a TD phone system. Which "speed dial numbers" are you trying to program? System speed dials, are stored in system program 001 and consist of a 3 digit number (may be 2) with a "9" in front and the number as you would dial it from the keypad. Personal speed dial numbers depend on the button you're programming it onto. If it's a button with a light, you dial "2" in front of it. If not, you don't. So, Program 99, button, and either 29 + number STORE or 9+number STORE programs a personal speed dial.

There are other programs to store under the tone pad keys. Those features are covered in your User's manual for the TD system.

Carl

Go to your phone call settings and activate speed dials feature.
Then come back to your phone in normal display mode,press and hold any desired digit e.g 2,3,4,5,6,7 on the key pad and follow the prompt for assigning of phone nos for speed dialing.

You will need the model number & go to this site.
http://www.home-electronics.net/ge/pc/user-manuals.asp

By programming, these are programs 000,001 and 002 for Date and Time, Speed Dial number, and Speed Dial Name.

Date and time programming is easy, I don't wish manual speed dial entry on my worst enemy. However, if you like a challenge, I'm going to give you a link to the programming manual.
http://public.carl.airpost.net/TDA/TDA_PTPM_32.pdf

Start with page 12, since you'll need it to get into programming.
Your key sequences begin on page 16. After you put the first 5 or 10 speed dial numbers and names in, you'll get the hang of entering names in the directory. Nothing changes until you press ENTER or STORE. Each speed dial number starts with a trunk access code (usually 9) as part of the number. In name entry, each time you press the key it changes a letter. In a TDA IIRC 7 presses of the 2 key will get you ABCabc2.

Carl

I found the model no, on the Uniden website DSS 7805WP and down loaded the manual.. there were no instructions .. but i showed where the phone book icon was .. and once inside the phone book the process was the same as the handset that came with the answering machine.

First thing u need to learn that u can speed dial feature only for buttons from 2-9. So u need to first assign the no to one of the nos between 2 and 9 on the keypad, and then u can use ur speed dial feature...!!! Hope to recieve a good rating from u...!!!

Thankyou