Question about Yamaha RX-V673

1 Answer

Yamaha RX V673 airplay problem

The receiver is visible on my home network, it has a fixed IP but is not visible in itunes on my laptop so airplay does not work, how can i fix this?

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Disable IGMP filter on your router

Posted on Dec 18, 2012

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
smarthome2
  • 1114 Answers

SOURCE: Yamaha receiver RX-V663

Make sure you have an analog RCA audio cable from the source to the receiver. Digital coaxial or optical will not work for zone 2 or zone 3. By adding an analog cable it will not affect your main zone, it will always go to digital first. Hope this helps

Posted on Dec 29, 2009

Testimonial: "great feedback. "

  • 236 Answers

SOURCE: Yamaha RX-V 800

Go to yamaha service direct they should have the parts. impossible for this model to be phased out. this is a model about 6 years ago only. they still have the parts for that. Power output and driver transistors are industry standard, replaceable too byt other newer model. you just need to find a real good techie for yamaha... i mean yamaha expert

Posted on Mar 19, 2008

easyq
  • 144 Answers

SOURCE: on zone 2 of my yamaha rx v663 receiver it says fixed when I try to adjust the vlume and won't let me cut it up or down.

Check the setup menu of the receiver on zone 2 settings most likely the error is a fixed volume setting for this zone. If not found, reset factory settings and try to setup everything again. If the problems persists, contact your vendor if still under warranty.

Posted on Apr 17, 2009

  • 8 Answers

SOURCE: No volume in Zone 2

Get the original Yamaha remote, go to Set menu, manual setup, speaker setup, and look for "extra speaker." it needs to be set to "zone 2." This is off the top of my head, so it should be pretty accurate. Get used to doing this, though, as this amplifier assignment to zone 2 is prone to resetting itself in those Yamahas.

Posted on Sep 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My RX- V673 Yamaha receiver won't turn on. I have power and the stand by switch is on


Try holding the 'tone control' and 'info' buttons and press power. This will unlock it if it is protect mode. If it turns back off right away, then you most likely have a problem in the amp circuit which needs to be repaired.

Jan 17, 2017 | Yamaha RX-V673

1 Answer

How to connect my JBL JRX 115 speaker to my Yamaha RX V673 receiver


You would use a standard banana plug to either a 1/4 phono or speakon plug. The JBL JRX 115 has both on the back. All the outputs on the Yamaha RX V673 have banana plugs. The channel you plug into would be up to you, there are many choices and they are listed on the back of the unit.

Dec 03, 2013 | JBL Audio Players & Recorders

2 Answers

Where do you find IP address


Internal Ip address can be found by the following steps
1)Go to start menu
2)choose run
3Just type cmd into the search box
4)Command prompt will appear
5)type ipconfig
it will show your IP address of your system.

External Ip can be traced out using Ip-details.com .

Nov 05, 2013 | Yamaha RX-V673

1 Answer

Yamaha Receivers have International Warranty?


Just send an E-Mail to Yamaha's customer service section. I'm certain they will be able to tell you.
The only other problem you might encounter is if the USA model uses a different mains system to the one in Brazil.

Jun 01, 2013 | Yamaha RX-V673 7.2-Channel Network AV...

1 Answer

My sub wont power off when I turn off my Yamaha RX-V673


The sub would have to be getting AC power from an outlet on the Yamaha

Jan 08, 2013 | Yamaha RX-V673

2 Answers

Yamaha receiver will not connect to Airplay


I have the same problem, it seems the airplay connection is easily lost, it never plays for longer than an hour without itunes losing the receiver, then i have to reset the receiver so that it appears in itunes again, very annoying. I spoke to Yamaha and they are not aware of any issues but clearly there is one. A quick workaround is to bring the receiver up in a browser by typing in its IP address, go to IP Address tab and simply apply without changing anything, this causes the receiver to initialize its network function as you will see the amp resetting and it will then appear in iTunes. This doesn't work through the units setup without changing settings and then changing them back again. Hopefully this is just a glitch that will Yamaha will fix in the next firmware update, I am running 1.14 update.

Sep 28, 2012 | Yamaha RX-V473 5.1 Channel Network AV...

1 Answer

Airplay not working


I had the same problem. You can disable IGMP filter on your router. It will fix it.

Jul 29, 2012 | Yamaha RX-V673

Not finding what you are looking for?
Yamaha RX-V673 Logo

Related Topics:

1,859 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5686 Answers

The Knight
The Knight

Level 3 Expert

76100 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...