Cannot access belkin 54g wireless modem settings

Samay,

You should reset your router to clear all information from it. The best procedure to fully clear your device would be to press the reset button with power on for 30 seconds; while continuing to press the reset button, remove power from the unit; and while continuing to press the reset button restore power for 30 seconds.

You should now be able to access the menus after the unit boots up with the default user name/password for the unit. If you do not know them, just Google [your router name] default user name and password. You can now set up the router to meet your requirements. There is a lot of information that will help you on the Internet, but having a clean booted router is important to start with.

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then click on wireless settings->wep security add password then save settings and restart router then you can connect wireless with that password. . Let me know if you need further assistance. Thanks for using FixYa.

If you can access the configuration page of your belkin router you have to copy the MAC address of your computer to the router. The router has the capability to clone the MAC address. It's because if you have a cable internet connection the MAC address is registered in the server.

From one of the "wired" computers, connect to the router's built-in web-server, and run the "Wireless Networking Setup Wizard", in order to configure your wireless network, choosing an 'SSID' and a "password" for your network.

connect your router to computer with ethernet cable.
Then you can access it with following link.
for belkin routers http://192.168.15.1
for other routers
http://192.168.1.1
or
http://192.168.0.1


type user as "admin" and password as "admin" or blank or "password"
Then you can see configuration page of router.Click on wireless and If you want secure router then enable WEP security then add new code it is your password key for connect wi fi.
Let me know if you need further assistance.

Go to the setup page for the router (IP 192.168.1.1) and set up the WPA-PSK [TKIP] security. It will allow fairly simple setup, and only provide the pass code to house members.

To access in your router, open a blank Browser page and type :
http://192.168.2.1 normally it's this ip :)
(note that A lot of routers setup pages are accessed through [192.168.1.1]).

username : Admin and at password leave it blank otherwise Type : admin

go to router settings as admin and select wireless settings->security. There you will find the WEP key written. Either note it down or change it to something that you can remember. And save.

This is more of an explanation then a solution, but to best explain what to do I have to first explain why this is happening. When you add security to a wireless router or ap you add extra envelopes to the packets of info being transferred, adding encryption to that makes it much slower because the ap has to encode all packets coming to you and un-encode all packets being sent to the Internet. In our time this happens very quickly, but in computer time I just described a lifetime. In addition if your signal is not 100% you might have packet loss "more slow down". Now the answer, in your ap setup pages you can setup wireless security, set this to Mac address authenication and add the mac addresses of all the network cards that have access to this ap. This is by far the fastest methiod of secure data transfer.

Hope this was some help...
Tim

hey what you can do is you can reset the entire router... by using the reset button on your belkin router... Or else you can also access the router by using the following IP address in the internet exlorer...

try 192.168.1.1 or 192.168.1.0 & then go to the wep settings & reset the router or change the password for the router...