I tried to replace the buld in my Sharp Projector with a siiliar model. The bulb did not work bt the fan did not either. Is the proper bulb associated with the fan runnung?
The model you posted is wrong, find the right model here and download the reset operation.
Hi,
RESETTING THE LAMP HOUR COUNTER
1. Turn the Master Power off using the red button located near the AC input
jack.
2. Hold down the “ENTER”, “ADJ!” and “ADJ"” buttons simultaneously on
the projector. While keeping them depressed, turn on the Master Power
with the switch near the AC input jack. (See diagram below)
3. The unit should power up when you do this and the lamp should light.
Look for “000H” to be displayed on the screen, which will confirm you have
reset the counter to zero.
Note: It is possible that you may have to perform these steps 4 or 5 times
before it works correctly. Also, on some models, you may have to continue to
hold the buttons and press the Power button on the front of the unit after
turning on the Master Power.
Hope this helps
Chris (ziraffa)
SO, it's Enter, ADJ down and Adj right:
Buy the correct bulb and install it and go through these steps, it will work :)
Chris (ziraffa)
For your information, the unit is designed prevent the lamp from lighting when the lamp counter has been used for 1900 to 2000 hours. This is to protect the lamp module. When this occurs, you just replace the lamp module with a new one and use the above procedure to reset the counter.
×
Hello,
Just to shoot another perspective here...
Did you happen to replace the lamp door whe you changed the lamp? It won't allow the lamp to start if the door is not replaced or replaced incorrectly.
Hope this helps you...
Hi, please check if any fuse has gone bad. May be thats no part is working in it.
Here is a video on changing the lamp. VIDEO The replacement lamp can be ordered at the following: LAMP REPLACEMENT . Let me know if you still need help.
Sharp Lamp Specifications
Spec
Data
ProductCode
BQCXGE1000U1
Type
Genuine Original Lamp & Housing
Warranty
90 Days
Hi and welcome to FixYa,
Initially, check;
Good luck and Thank you for using FixYa.
Incidentally, one other responder, Dipu007 has copied some tech tips from United Visual addressing lamp timer/counter reset.
HI,
It is generally recomended to put the bulb in the projector that is company certified .Take the old bulb out and put the old bulb back in check , if there is movement of the fans .
For authorised parts and serice you can contact sharp
1-800-237-4277, 1-800-BE SHARP
Thanks
proton
Its recommended that you replace a bulb with the same original product as 3rd party bulbs may generate too much heat or other disfunctions.
IF the fan runs fine on the old bulb and it stops runing when you swap in the new bulb, the problem must be your new bulb.
The fan won't run without the bulb in the device and the fan won't run unless it is at a certain temperature either
bestdarngood
simple enough to reset the counter
first remove the case( five screws in the back and slide top completly off carefully so u dont tear the sound cable connected at the front unplug it and set aside..... now all u do is hit the small button on the top of the motherboard with the unit plugged in. DO NOT HIT the switches just the small button!(doing so will shut down the fans and your bulb will have to cool manually which is VERY BAD FOR THE LIFE OF THE LAMP) a prompt will come up. Now go to sss choose system then lamp then hit enter where it says lamp. counter will reset.
×
The bulb has to be replaced with the same model number and not with the similar ones.such things wont solve the problem.use the exact bulb and it will solve the problem.
Most Sharp projectors require you to perform a reset procedure once you have installed a new lamp. This resets the lamp hour counter so it properly keeps track of the lamp hours for the new lamp. To insure the lamp hour counter will be correct, Sharp built-in a function to disable the lamp until this counter has been reset. The reset procedure can be found in the owner's manual on most models. If you have misplaced the manual or the reset procedure is not in it, contact us and we will e-mail you the procedure. Note: If you have performed the procedure and it doesn't seem to have worked, don't give up yet. On some models, the reset procedure sometimes needs to be preformed several times before it works. No one seems to know why, so just be persistent.
78 views
Usually answered in minutes!
Please email me the reset instructions for the lamp replacement. I have a BQC=XVH37U//1 lamp on hand. Will it work in this projector?
Still waiting on instructions to reset the hour counter on my projector.
×