Kenmore Freezer display alternating between temperature and CE

CE probably means a Communication Error between the high and low voltage boards of the freezer. First check if your freezer uses a 9V backup battery and replace that with a new one. Next check the wiring for corrosion or damage. Check where the wires connect to the boards and inside the door. (Note: the high voltage board controls the compressor.) You may want to check that the freezer is holding the correct temperature with a refrigerator/freezer thermometer.

Please add a comment with the model number of the freezer (including the three digit prefix) if you'd like me to check for a parts diagram and parts list.

I hope this helps.

Cindy Wells

Search Results

Freezer electronic temperature control manual... ' Sears ...

www.searspartsdirect.com > Ask an Expert
Jul 5, 2012 - I have a Kenmore elite freezer with electronic temperature control. ...my freezer was delivered yesterday, the control panel is stuck on of, ... an electronic control on front. the display is showing hi temp and door ajar. also an l in ...

Control Panel is not working right - Samsung

www.samsung.com/sa_en/support/skp/faq/239315

Samsung ElectronicsSep 3, 2015 - In case of wrong temperature display, possibly door opens so inside ... If the control panel is still not lit up after you plug the refrigerator back in, it may ... When initial installation, Temperature will show current temperature for a ... When the refrigerator/ freezer reach the set temperature, the blinking will stop.

Adjusting Side-bySide Refrigerator Temp Controls - Actual ...

? 3:50
https://www.youtube.com/watch?v=DFzTGKVo79g
Jun 27, 2010 - Uploaded by GE Appliances
CAN I TURN OFF THE DIGITAL CONTROL ON FREEZER AREA ONLY. ... I need to know How to reset this kind of refigirator, same front panel ... When you try to set the actual temperature, does your control show your new ...

Electronic Temperature Controls - ManualsLib

Kenmore & Whirlpool refrigerator frost build up in freezer not ...

? 7:02
www.youtube.com/watch?v=gVXT7pZyk_o
Sep 12, 2013 - Uploaded by ApplianceVideo.com Service a Kenmore Upright Freezer which has the following problems: Not Cooling Properly At: http ...

Freezer Troubleshooting - What to Check Before You Call a ...

www.realestate.com > Realestate.com Blog > Articles
Aug 12, 2012 - Alternatively, if the freezer is in a defrost cycle, it will not kick on immediately, the temperature ... Refrigerant circulates through coils, spreading coldthrough the unit interior before .... We have a kenmore upright deep freezer.

You have a bad freezer fan and need to replace it. The fan is located behind the back wall INSIDE the freezer. The unit will warm up a little because the air wont circulate the way it is supposed to. You can try unplugging fridge for 30 seconds to reset the control board u can do it yourself although I don't recommend it because u need actual diagnosis but this seems it hope it helps try buying part from sears or amazon

maybe your door switch stock up try to replace or dismantle swicth .reset your alrm unplug the unit after several minutes. plug the unit observe operation.

http://www.managemylife.com/mmh/owner_manuals/370/KENMORE-Upright-Freezer-L0805601?brand_name_search=Kenmore+freezer+2532846.2801
try this web site that has a copy of a manual for this freezer. See if this has what you are looking for.

Check the some wiring or the motor.. but if you confusing of you capability look the nearest service center of Freezer in you area

It sounds like this is a a non DIY issue. there is really not much you personally can do.
Contact an authorized servicer fir best results

Good luck!

I’m happy to assist further over the phone at https://www.6ya.com/expert/david_dc2f9e0a44104720

No, not necessarily a lemon. With the higher percentage of electronic controls being used in appliances these days it happens - and is no small cost. My advice to you is bite the bullet and DON'T repair it, buy a new one, with an extended service warranty.

First make sure you have a good 9v battery installed. If it is ok then the problem will probably be in the display board or the wiring connectors between the boards. CE is communication error. If your model has the electronic tempature control instead of mechanical thermostat the problem could be in there. My bet is a bad connection at display board.