Error message every time i get on my scale it reads error 2, what does this mean and how can i fix it?

E. If the device is showing the error "E" on the message screen, check to make sure that you are not moving while calculating the weight. ... If after this the error message hasn't gone away, there may be bad connection on your scale.

Health o Meter HDR743 Troubleshooting - iFixit

https://www.ifixit.com > Wiki > Health_o_Meter_HDR74...

How to Reset a Health o meter Scale ' Hunker

https://www.hunker.com > ... > Other Home Appliances
Performing the action allows the scale to display the correct weight. You may also need to do this if the scale's display shows the letter "E." Doing the reset ...

Why does my Health o meter scale read e? - FindAnyAnswer ...

https://findanyanswer.com > why-does-my-health-o-me...
May 6, 2020 - Stepping on the scale before the "000.0" causes this error message to appear. If "E" appears, step off the scale and repeat initial RESTART by ...

Step 1
Step lightly on the scale until it displays "--", "0000" and turns off if you receive the error "ERR0," which means the scale is not initialized. Initialization must occur after each battery installation.
Step 2
Set the scale on a flat, even surface, not on surfaces such as carpet if you receive an error "ERR1."
Step 3
Step off the scale and wait for it to reset before stepping on it again if you receive an "ERR2," which often means the unit was jarred or overloaded. Also, if you weigh more than the maximum weight capacity you will receive this error.
Step 4
Remove your shoes and socks and wet your feet slightly with a damp cloth if you receive the "ERR3" error. ERR3 is a contact error and your feet should ideally be bare and wet to achieve an accurate body-fat reading.
Step 5
Step off the scale and wait for it reset. Remove your shoes and socks and wet your feet slightly if you receive either the "ERR4" or "ERR5" errors, which means your body-fat or body measurements are out of range.
Step 6
Reset the scale if it doesn't work or you continue to receive error messages. Remove the battery and set the scale on a flat surface. Stand still on the scale for five seconds and step off. Re-install the battery and place the scale back on the flat surface. Place one foot on the scale until it displays zeros or dashes. Remove your foot and wait for the scale to turn off. Step back on the scale to weigh yourself.
Step 7
Replace the battery if you receive a "lo" or "bat" error.

Remove your shoes and socks and wet your feet slightly with a damp cloth if you receive the "ERR3" error. ERR3 is a contact error and your feet should ideally be bare and wet to achieve an accurate body-fat reading.

Step off the scale and wait for it reset. Remove your shoes and socks and wet your feet slightly if you receive either the "ERR4" or "ERR5" errors, which means your body-fat or body measurements are out of range.

Reset the scale if it doesn't work or you continue to receive error messages. Remove the battery and set the scale on a flat surface. Stand still on the scale for five seconds and step off. Re-install the battery and place the scale back on the flat surface. Place one foot on the scale until it displays zeros or dashes. Remove your foot and wait for the scale to turn off. Step back on the scale to weigh yourself

Douglas, it means usually means over loaded, it is an error message.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

http://www.srinstruments.com/manuals/MAN310.pdf

I have facing problem in seca 703.when it start it showing 000000 digits on display and then it blinking this same digits on display...

Most likely HHH represents an error message telling you the weight of them item is higher than the scale can handle. For example if you had a very sensitive scale that weighed up to 50 carats and you put a 250 carats ring on the scale, it would give you an over load error message.

my scale does the same thing. battery reads 2.85 volts. could that be a low reading for a lithium battery with a 5 yr guarantee? hmm.

From the Taylor Site http://www.taylorusa.com/faq-scales

Here are the basic ERR messages and their meanings:

• Error 0: Initialization
• Error 1: Instability (scale is on an uneven surface ex: carpet)
• Error 2: Unit may have been jarred or unit was overloaded (customer went over the maximum weight capacity)
• Error 3: Contact error (Feet were not wet for Body fat reading, feet aren’t big enough to reach sensors)
• Error 4: Body fat is out of range
• Error 5: Water is out of range

I got an ERR2 message and now the scale doesn’t work. What should I do? The following reset procedure is used when the scale shows an err2, err, 0.0, inaccurate weight, or some other unusual error.

1. Remove the battery from the scale.
2. Sit the scale on a hard surface floor.
3. Step up onto the scale, stand still for about 5 seconds and step off the scale.
4. Re-install your battery.
5. Place the scale back on a hard surface floor.
6. With one foot only, place just enough weight on the scale for the display shows zero’s or dashes. Once you see zeros or dashes remove your foot.
7. Wait for the scale to turn off again.
8. Step up onto the scale for a weight.

If the reset is successful, you should receive a weight right away. If you continue to receive one of the error messages above please call our Customer Service department or contact us via email. You can also try the reset procedure a 2nd time. Sometimes the reset procedure will work the second time.

This is a reply I received from Taylor customer support. I have followed this procedure enough times to wear out the original battery and still get the Err 1 message. You may have better luck.

Thank you for your e-mail. The reboot below may clear the error from
your scale. You may need to do this several times to completely reboot
the system. Please let us know if you have any questions or continue to
display the Error.


1. Remove the battery from the scale
2. Set the scale on the floor without the battery in place.
3. Stand on the scale for 10 seconds (still without the battery)
4. Carefully replace the battery without turning the scale on.
5. Using only one foot, tap the scale or apply just enough pressure to
turn on the display. (It should show dashes or zero's) IMMEDIATELY
REMOVE YOUR FOOT.
6. Let the scale turn off
7. Step on the scale for a weight reading


Regards,


Linda DLT
Consumer Relations
Taylor Precision Products
& Salter Housewares
2220 Entrada del Sol, Suite A
Las Cruces, NM 88001
Toll free - 800-289-0944
866-843-3905
Direct - 575-526-0944 ext 3172

Hello,
If the scanner read only two times is a problem with the communication protocol.

What protocol do you use?

Explain more about your problem with your calibration pricedure