Question about Tacsew T500

1 Answer

Is there a way to slow down the motor on a Tacsew blindhemmer machie

Want to slow down the motor someway for better control. the motor is under the table the machine sits on and is connected by a rubber belt

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Tacsew Master
  • 7,365 Answers

Try adjusting the foot pedal, there are jam nuts under the foot pedal
to make it go slower or faster.

Posted on Sep 27, 2012

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Tacsew T500 : Needle continually comes unthreaded

No this machine does not use a bobbin. I just purchased one too and called the supplier to help me keep mine threaded. He said they do not take much tension at all. So check your tension and then when threading it, make sure your thread goes under the bar in the center of the tension disk, not on top of.
Good luck, once you get it going it does a beautiful job!!!! Love it, Love it!

Posted on Jan 28, 2008

riclap
  • 3 Answers

SOURCE: tacsew lu-563 sewing machine

Generally going to have to be addressing the drive motor, either substituting a lower speed clutch motor for the existing one, ie if you have 3000 rpm motor, then going to a 1725 rpm motor. Alternatively, selling the clutch motor and buying a servo motor instead, which should be available with a variable maximum speed control. The Sewquiet 4000 can select different speed ranges with the flick of a switch. If you already have a servo motor and it does not have a variable max speed, then switching the drive pulley on the servo motor to a smaller size should help
A more convoluted solution would be building a support under the table for a layshaft with different pulley sizes so that the motor could drive one pulley and then a smaller pulley on the shaft would drive the sewing machine. Not a bolt on solution but pretty cheap to do if you are good at fabricating.

Posted on Jan 01, 2009

  • 255 Answers

SOURCE: How do you slow down the running speed? Is there a

Techsews are industrial sewing machines. Check out http://shop.raphaelsewing.com, especially their web blog. It's full of great information on Techsew machines.

Posted on Jan 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DOES THE TACSEW T1718 MACHINE SEW IN A ZIG ZAG


Does it have a Stitch Width control? If not, it is probably a limited stitch only. Most Tacsew machines are made for high speed industrial sewing and frequently are made to perform a limited number of stitches. It appears this is a blindstitch for hemming.

Tacsew T1718 4 Full Size BlindStitch Hemmer Machine 1718 TAIWAN 8mmLift 3...

TACSEW T1718 YouTube
..

Oct 26, 2016 | Tacsew Sewing Machines

1 Answer

Can a Tacsew get fix if the motor lock up?


sounds like the spool case is jammed up
take the spool case out

check the drive belt is ok

in some you just need to remove the case
and tighten a screw on the drive sproket inside
you can find the plastic spleen holder on the drive wheel has stripped
or cracked so the motor will run and nothing moves

your post is too sparce on info
like does the motor run at all?????

usual problem is the motor runs no drive
because the drive belt is broken or a plastic is cracked

Dec 04, 2014 | Tacsew Sewing Machines

1 Answer

Motor growls


How long has it been since it has been serviced?

Mar 29, 2014 | Tacsew Sewing Machines

1 Answer

Model tacsew tm 10l-e. repair motor brushes


http://www.american-sewing.com

if i cant find brushes i simply take a set of other brushes that has a good connections to use
and file them the right size
use some calipers

Jan 06, 2014 | Tacsew Sewing Machines

1 Answer

Pressure foot wont stop


Sounds like a failed clutch brake on a clutch motor. I would replace that with a servo motor. You will like it much better.

Sep 08, 2012 | Tacsew Gc66 Sewing Machine

1 Answer

How do you slow down the running speed? Is there a reestat for this machine? The motor is a Tacsew Clutch Motor, Model RM1878-1L, 1/2 hp, Sr. # HMC 04051325


Techsews are industrial sewing machines. Check out http://shop.raphaelsewing.com, especially their web blog. It's full of great information on Techsew machines.

Jan 26, 2010 | Tacsew Sewing Machines

2 Answers

Tacsew lu-563 sewing machine


Generally going to have to be addressing the drive motor, either substituting a lower speed clutch motor for the existing one, ie if you have 3000 rpm motor, then going to a 1725 rpm motor. Alternatively, selling the clutch motor and buying a servo motor instead, which should be available with a variable maximum speed control. The Sewquiet 4000 can select different speed ranges with the flick of a switch. If you already have a servo motor and it does not have a variable max speed, then switching the drive pulley on the servo motor to a smaller size should help
A more convoluted solution would be building a support under the table for a layshaft with different pulley sizes so that the motor could drive one pulley and then a smaller pulley on the shaft would drive the sewing machine. Not a bolt on solution but pretty cheap to do if you are good at fabricating.

Apr 07, 2008 | Tacsew Sewing Machines

1 Answer

Tacsew T500 : Needle continually comes unthreaded


No this machine does not use a bobbin. I just purchased one too and called the supplier to help me keep mine threaded. He said they do not take much tension at all. So check your tension and then when threading it, make sure your thread goes under the bar in the center of the tension disk, not on top of.
Good luck, once you get it going it does a beautiful job!!!! Love it, Love it!

Oct 31, 2007 | Tacsew T500

Not finding what you are looking for?
Tacsew T500 Logo

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tacsew Sewing Machines Experts

Nick Olsen

Level 2 Expert

195 Answers

Ruth summersides

Level 3 Expert

1370 Answers

ray gallant
ray gallant

Level 3 Expert

63539 Answers

Are you a Tacsew Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...