My camera say err CF

Hello :

Here is what Canon said according some forums :

To isolate the cause of the issue, we suggest that you do the
following:

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.

Does the "ERR 99" message appear? If it does, then the camera should
be serviced. If it does not, then please proceed to the next set of
steps:

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.

Does the "ERR 99" message appear? If so, then the CF card is the most likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.

If the "ERR 99" message only appears when one particular lens is
attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.
I hope this will help .

please don't forget to rate !

Hello:

Here is what Canon said :

To isolate the cause of the issue, we suggest that you do the
following:

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.

Does the "ERR 99" message appear? If it does, then the camera should
be serviced. If it does not, then please proceed to the next set of
steps:

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.

Does the "ERR 99" message appear? If so, then the CF card is the most likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.

If the "ERR 99" message only appears when one particular lens is
attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.

I hope this will help

please don't forget to rate !

hi,

I do not know if this is going to be of any help. I was actually reading about this error code 99 in canon, and bumped into a forum, where people had share their experiences. You can give it a try. But if your camera is still under warranty, it is best to ring technical support.

"ERR 99" is a general error code displayed by the camera when the camera knows that something is not working properly, but not exactly what.

This error is typically associated with lens communication or shutter mechanism issues. To isolate the cause of the issue, we suggest that
you do the following:

1. Turn off the camera.

2. Remove the lens, battery, and CF card.

3. Allow the camera to sit without power for approximately 20 minutes.

4. Insert a fully charged battery, and turn on the camera.

5. Depress the shutter button as you would to take a picture.

Does the "ERR 99" message appear? If it does, then the camera should be serviced. If it does not, then please proceed to the next set of steps:

1. Turn off the camera.

2. Insert the CF card.

3. Turn on the camera.

4. Format the CF card in the camera.

5. Depress the shutter button as you would to take a picture.

Does the "ERR 99" message appear? If so, then the CF card is the most likely source of the issue. Try using a different card.

If the message does not appear, please complete the following steps:

1. Turn off the camera.

2. Clean the lens contacts by gently rubbing them with a pencil eraser or soft cloth. Be careful that you do not let any debris fall into the
camera body.

3. Reattach your lens.

4. Turn on the camera.

5. Depress the shutter button as you would to take a picture.

If the "ERR 99" message only appears when one particular lens is attached, then that lens should be examined by a service technician.

If you see the "ERR 99" with a different Canon lens attached, then the
camera should be serviced.

Hope this helps !!!

I Googled the error code you're getting, and found a list of things to try and steps to attempt directly from Canon. Try out some of the stuff below, it should help.

To isolate the cause of the issue, we suggest that you do the following:
1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.
5. Depress the shutter button as you would to take a picture.
Does the “ERR 99′ message appear? If it does, then the camera should be serviced. If it does not, then please proceed to the next set of steps:
1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.
5. Depress the shutter button as you would to take a picture.
Does the “ERR 99′ message appear? If so, then the CF card is the most
likely source of the issue. Try using a different card.
If the message does not appear, please complete the following steps:
1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.
5. Depress the shutter button as you would to take a picture.
If the “ERR 99′ message only appears when one particular lens is attached, then that lens should be examined by a service technician.
If you see the “ERR 99′ with a different Canon lens attached, then the camera should be serviced.

Try the following diagnosis steps: -

To isolate the cause of the issue, do the following: -

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert only a fully charged battery, and turn on the camera.
5. Depress the shutter button as you would to take a picture.


Does the “ERR 99′ message appear? If so, the camera may be faulty and requires a service. If it does not, then: -

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.
5. Depress the shutter button as you would to take a picture.


Does the “ERR 99′ message appear? If so, then the CF card is faulty. Try a different card. If the message does not appear: -

1. Turn off the camera.
2. Clean the gold contacts on the lens by GENTLY rubbing them with a pencil eraser or soft cloth. Keeping the camera face pointing down, also clean the gold contacts on the camera, being careful that you do not let any debris fall into the camera body.
3. Reattach your lens.
4. Turn on the camera.
5. Depress the shutter button as you would to take a picture.
If the “ERR 99′ message only appears when one particular lens is attached, then that lens should be examined by a service technician.
If you see the “ERR 99′ with a different Canon lens attached, then the camera is faulty and should be serviced.

Nope, this is not card anymore.

As you know CF is card failure, sometimes this cause to start error 99 , that is lens error , even if there is no problem with the lens.

This happens because the built in software in the camera can get messed up after an error CF.

You fix the problem calling Canon, they will guide through upgrading the firmware in your camera.

First ensure that you are using the camera menu and command to format the new card, and that new cards are properly inserted into the machine.

Call Canon support to get a firmware upgrade.

Not all CF cards are created equally, so yes, it could be your batch of cards. To determine if the error is CF related, and not anything else, try the following steps which are used to diagnose err 99's

To isolate the cause of the issue, do the following: -

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert only a fully charged battery, and turn on the camera.
5. Depress the shutter button as you would to take a picture.


Does the “ERR 99′ message appear? If so, the camera may be faulty and requires a service. If it does not, then: -

1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.
5. Depress the shutter button as you would to take a picture.


Does the “ERR 99′ message appear? If so, then the CF card is faulty. Try a different card. If the message does not appear: -

1. Turn off the camera.
2. Clean the gold contacts on the lens by GENTLY rubbing them with a pencil eraser or soft cloth. Keeping the camera face pointing down, also clean the gold contacts on the camera, being careful that you do not let any debris fall into the camera body.
3. Reattach your lens.
4. Turn on the camera.
5. Depress the shutter button as you would to take a picture.
If the “ERR 99′ message only appears when one particular lens is attached, then that lens should be examined by a service technician.
If you see the “ERR 99′ with a different Canon lens attached, then the camera is faulty and should be serviced.

Try the following diagnosis steps, in this exact order. This will isolate the cause of the issue: -
1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert only a fully charged battery, and turn on the camera.
5. Depress the shutter button as you would to take a picture.

Does the “ERR 99" message appear? If so, the camera may be faulty and requires a service. If it does not, then: -
1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.
5. Depress the shutter button as you would to take a picture.

Does the “ERR 99" message appear? If so, then the CF card is faulty. Try a different card. If the message does not appear: -
1. Turn off the camera.
2. Clean the gold contacts on the lens by GENTLY rubbing them with a pencil eraser or soft cloth. Keeping the camera face pointing down, also clean the gold contacts on the camera, being careful that you do not let any debris fall into the camera body.
3. Reattach your lens.
4. Turn on the camera.
5. Depress the shutter button as you would to take a picture.

If the “ERR 99" message only appears when one particular lens is attached, then that lens should be examined by a service technician.
If you see the “ERR 99" with a different Canon lens attached, then the camera is faulty and should be serviced.

Although you may have cleaned the lens contacts, did you clean the camera contacts? This is a bit harder but it’s doable: just hold camera so lens opening points down so no gunk falls in. Erase lightly. I used a lens cloth and dabbed at the contacts rather than blow them so as not to blow the erasings inside the camera.

1. Turn off the camera.
2. Remove the lens, battery, and CF card.
3. Allow the camera to sit without power for approximately 20 minutes.
4. Insert a fully charged battery, and turn on the camera.
5. Depress the shutter button as you would to take a picture.
Does the “ERR 99′ message appear? If it does, then the camera should be
serviced. If it does not, then please proceed to the next set of steps:
1. Turn off the camera.
2. Insert the CF card.
3. Turn on the camera.
4. Format the CF card in the camera.
5. Depress the shutter button as you would to take a picture.
Does the “ERR 99′ message appear? If so, then the CF card is the most
likely source of the issue. Try using a different card.
If the message does not appear, please complete the following steps:
1. Turn off the camera.
2. Clean the lens contacts by gently rubbing them with a pencil eraser
or soft cloth. Be careful that you do not let any debris fall into the
camera body.
3. Reattach your lens.
4. Turn on the camera.
5. Depress the shutter button as you would to take a picture.
If the “ERR 99′ message only appears when one particular lens is attached, then that lens should be examined by a service technician.
If you see the “ERR 99′ with a different Canon lens attached, then the camera should be serviced.


From RICHARD'S NOTES

cleaning the contacts ought to be done using a pencil eraser(i am very specific about this)to fix this error
vigorously scrub the lens contacts with an eraser. Then  gently use the eraser to clean the camera contacts (holding the contacts face-down to prevent eraser rubber from falling into the body).Put the lens back on… and the camera shoudl be fixed!
Try this and post back before you rate..