Convergence not lining up

The tv have a problems known as a convergence problems,it dead.Tv have colors lines R,G,B mis alignments,have colors shadow pictures or 3D pictures look alike?The tv convergence board is dead.The tv convergence board must have replace the 2 STK convergence ICS and some or all of it resistors too.To fixed the tv convergence board to solved the tv convergence picture problems.The shop,will cost u like $300-350 for parts and labors.

hi, sounds like a convergence issue. try this...

Look through your manual. Your manual will always give you the most specific directions for your particular model. Look for an "adjusting convergence" or "set manual convergence" section.

Enter the menu on your TV. Use the remote control and bring up the menu.

Choose "Convergence." This may be under "Picture Settings," "Function" or "Advanced Options."

Select a color. You will have red, green and blue to choose from. Do each one, starting with red.

Press "Enter." A crosshair pattern will appear on your screen.

Adjust vertically. If there is a horizontal red line visible, press the up or down arrow keys (or channel up or down) to adjust the convergence until the line is superimposed on the horizontal-center line of the white crosshair.

Adjust horizontally. If there is a vertical red line visible, press left or right (or volume up or down) to adjust horizontally. Do this until the line is superimposed on the vertical line of the white crosshair.

Save settings. It is important to save your settings when you are done, instead of simply exiting the menu.

Repeat these steps for all colors.

good luck!

Tv have convergence problems,it dead.Colors lines R,G,B don't aligned.The tv convergence board is dead.The 2 STK convergence ICS and some or all it resistors are dead,these parts must be replaced to solved the tv pictures covergence problems.The shop,will cost u $300-350 for parts and labors.

Hello,

To get the code to enter on your remote to engage multipoint convergence adjustments, you need to contact the rca customer care for that, you get them your model number and they will get your code for you.

To process and save the adjustment made, follow the steps below;

1. Look through your manual. Your manual will always give you the most specific directions for your particular model. Look for an "adjusting convergence" or "set manual convergence" section.
2. Enter the menu on your TV. Use the remote control and bring up the menu.
3. Choose "Convergence." This may be under "Picture Settings," "Function" or "Advanced Options."
4. Select a color. You will have red, green and blue to choose from. Do each one, starting with red.
5. Press "Enter." A crosshair pattern will appear on your screen.
6. Adjust vertically. If there is a horizontal red line visible, press the up or down arrow keys (or channel up or down) to adjust the convergence until the line is superimposed on the horizontal-center line of the white crosshair.
7. Adjust horizontally. If there is a vertical red line visible, press left or right (or volume up or down) to adjust horizontally. Do this until the line is superimposed on the vertical line of the white crosshair.
8. Save settings. It is important to save your settings when you are done, instead of simply exiting the menu.
9. Repeat these steps for all colors.

Take care

According to the manual:
1) go to the "TV Main Menu"
2) Select "Screen"
3) Select Adjust Projection TV (obviously only if a projection TV).
This then allows you to adjust the TV's 3-colors. Selecting GREEN CENTERING brings up a control panel that lets you center the green projection tube on the screen. Selecting RED CONVERGENCE or BLUE CONVERGENCE lets you align the Red & Blue projector tubes. Centre the green projector tube 1st. Then adjust the red & blue until the test pattern on the TV screen appers white.
Good Luck!

Your TV most likely has a Convergence Chip Failure ( common problem )

Here are some of the most common symptoms and example photos of a convergence problem

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.

Solution #1

You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together convergence repair kits for most models.

The kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, thermal paste, etc. Everything you will need to do the repair yourself.

Here are some of the most common symptoms and example photos of a convergence problem

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.

Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.



You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.


Solution


You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick email and they will put one together for you. Their kits includes photo instruction guides, original Sanyo STK chips, convergence resistors, pico fuses, etc.

Sounds like a convergence promblem.

Here are some of the most common symptoms of a convergence problem.

Screen looks 3D
One or more colors can't be adjusted when using the convergence menu.
Screen is bowed in or warped.

Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence or magic focus section.

Try to adjust the convergence.

You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.

Its a fairly easy fix on the Hitachi sets.

You can get a repair kit that includes all the parts from www.TvRepairKits.com. The kit includes a photo instruction guide, original Sanyo STK chips, convergence resistors, etc.
Everything you need to fix it yourself.

The problem is called green geometry.There is nothing wrong w/the green pix tube.It is critical to get the green geometry

accurate because the red and blue convergence overlays on

the green.If you have more than an alignment issue,that will need

repair before adjustments are attempted.