FreeMotion Tt30 Incline Trainer Logo
Linda Higginson Posted on Sep 06, 2012
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

We have a Free Motion Tt30 Incline Trainer making a loud noise that sounds like a bearing going bad, then the noise stops. Do you have any repair suggestions?

The first few minutes when the trainer is used is when the noise is loudest. The noise started about a month ago. Can you tell me how to care for this situation?

1 Answer

ernesto cuadra

Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

  • FreeMotion Master 12,223 Answers
  • Posted on Sep 07, 2012
ernesto cuadra
FreeMotion Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

Joined: Sep 03, 2011
Answers
12223
Questions
0
Helped
4080794
Points
34431

1) Lube the machine see the video and use the common sense, this happen because the lack of maintenancae according with the instr. manual. Shut down the machine for to protect the electronic system.

2) Lube the rollers bearing too, very well.

3) Test the input voltage motor, if there are the motor NEED repair.

4) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the block diagram.

God bless you
We have a Free Motion Tt30 Incline Trainer making  - 9_7_2012_11_57_29_am.gif

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My freemotion i5.3 incline trainer shut off while I was walking on it and now it will not turn back on.

I have a Freemotion i5.3 Incline Trainer. When I run on it at 4+ MPH it makes loud bangs when my foot land on the platform. I usually walk on it at higher incline and just recently started running on it. The bangs are much louder at 0% incline than at higher inclines for the same speed. What might be the problem?
1helpful
1answer
1helpful
2answers

My 2009 nissan altima has a loud growling sound

This could be one of two things. We will first start with a wheel bearing. When you are driving, does the growling noise get louder as you go faster. Some times is will sound like you have a helicopter flying beside you depending on how bad the bearing is. The second thing that could be causing the growling noise is your transmission. There are also bearings inside your transmission that could be causing the noise. If you have a cvt transmission, you have a 120,000 mile warranty and can have it repaired at no cost to you. You will just have to go to a nissan dealership.
0helpful
1answer

Tt30 is stuck at 3% incline and will not speed up or slow down. It also beeps continually and displays SB for about 5 seconds when first turned on. I tried the recalibration procedure and it does not...

please RUN the software calibration for easy diagnostic and fix it.
go to HOOD cover motor, and follow the steps, or ready your owner manual
God bless you
0helpful
1answer

Incline works but belt wont move

see the video and lube deck belt+rollers bearings
God bless you
0helpful
1answer

Front end makes loud noise while driving over 10mph and gets louder and hums down when i stop

It sounds like you may have a wheel bearing/ hub assembly starting to go bad...You can check this by jacking up the front end and checking for slight play in each wheel when you try to move tire in a side to side,and up and down motion basically But you just want to use a wiggle motion...you should be able to feel a bit of excessive play in the side which is going bad...One side will be tight with no play,and the other will have some play if the wheel bearing hub assembly is going bad...
0helpful
1answer

Whirlpool washer making loud noise when spinning

It sounds like you need a bearing job. The bearings in the back half of the wash tub go bad. and the washer gets loud .It's an expensive repair. I hope this helps
0helpful
1answer

My check engine light is on. There is a squeaky cricket noise when the car is in motion; it is not a loose belt. I don't want to take it in and be overwhelmed with major engine problems. Any ideas what it...

for the check engine light:
-you can go to auto zone and have them hook it up to the computer for free!!!!!

for the squeaky cricket noise:
-could possibly be a wheel bearing starting to go bad, or possibly a wear sensor on the brakes....

that is only if it makes the noise when the vehicle is in motion.... if the sound is there while it is sitting still, then you could have a pulley bearing going bad... hope this helps.... please rate this...
0helpful
1answer

Washer model PAVT244AWW agitation noise

Sounds like the motor is going bad. It will only get louder before it finally stops. There is a device that assists the agitation motion that may be bad or is going bad.
Not finding what you are looking for?

452 views

Ask a Question

Usually answered in minutes!

Top FreeMotion Exercise & Fitness Experts

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

920 Answers

john h

Level 3 Expert

29494 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66955 Answers

Are you a FreeMotion Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...