Question about Hotpoint 24 in. FDW60 Free-standing Dishwasher
Hi all, my 18 month old FDW60 has developed an error not described in the handbook. After turning it on selecting a program and pressing start it begins to make all the right noises, but after 10 seconds it beeps and the 'eco' light starts flashing, whilst continuing to make all of the right noises, but that is all it does because no water enters.Can anybody help. Thanks
I had this problem and discovered it was due to a leak. The float switch attached to the bottom panel was operating. Pull out the mains plug, tip the machine on it's side (water will escape so get a mop ready), remove the bottom panel, 3 screws front and back, disconnect the connector from the float switch. Tape the connecter up out of the way and stand your machine back up. Try running it now. If you have a leak somewhere then you will get a puddle under the machine. If no leak, then I would suspect the float switch itself.
Posted on Apr 13, 2007
After the flashing Eco light and refusal to do anything apart from run the pump..
I placed my dishwasher on its side and then righted it again after half an hour, it's now working again!
I have also had the two flashing lights in the past as well, solved by running dishwasher empty with a bottle of dishwasher cleaner.
Posted on Jul 23, 2008
Just want to say Thanks for saving me £90 and loads of time. 'Eco' light was flashing and discovered lower spray arm had become obstructed by cutlery slipping down through the basket during the cycle, and had come off. Fixed the arm back on okay but flashing continued. Tried the above solution but didn't even have to take the bottom panel off, Hubby just tipped the machine over and all the water came out of the base. Put it back up and tried it and it's fixed! Easy.
Posted on Dec 11, 2007
I love the internet! Had the same prob... Disconected the water in-pipe, tipped backwards for about 1 minute, had quick panic as I had totally forgotten to get towels to clear up the obvious amounts of water that were about to flood out. And hey presto, all working again. So dish washer fixed and dishes done all before wifey gets out of bed... Brownie Points!!!
Posted on Feb 13, 2010
Yep same here eco light flashing, tipped it up for 3 mins, again no towels (men eh!) , works like a treat
Posted on Aug 15, 2010
Absolutely fabulous! Same issue, followed the advice and hey presto a woring machine!
Posted on Jan 25, 2010
I tried this fix and it worked perfectly despite there being no apparent leak and the float & switch in full working order. Many thanks to Stevecon for the solution.
Posted on May 21, 2007
Just worked for me and the Mrs thinks I am the bees knees! Thank you all
Posted on Aug 28, 2011
I'd just like to say that I had exactly the same problem after my kitchen was flooded by the storms and in 5 mins....hey presto....it's working again. Thankyou very much for putting your expertise onto this page. It's saved me a shed load of money (not to mention washing up which I truly detest!)
Posted on Aug 03, 2007
I just wanted to add also that I followed the instructions here as I had the same problem and my dishwasher is working again! The only difference is, I tipped it back and just a trickle of water came out, so I moved the towels and tipped it forward instead which did the trick, however for some reason the water flooded out the back anyway which meant a quick switch of the towels again! But, thanks everyone who posted!
Posted on Aug 16, 2013
Tipping the machine on outside and drying the base after removing solved this problem.
Posted on Mar 04, 2013
It worked for me two. Put it on its side for 10 mins and it worked! Thanks so much!
Posted on Aug 25, 2019
Thankyou thank you thank you for this post eco was flashing and beeping draining but nothing else read this post pulled out dishwasher layed it ok it’s side for a few minutes turned it back on and yay it’s working old post still helping in 2019
Posted on Mar 13, 2019
Fast forward to 2015.... and the suggested solution worked perfectly - thank you!
Posted on Jul 02, 2015
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
In my case it was the pressure sensor on the side of the short hose between the main (circulatory) pump and the bottom jet arm (which spins inside the machine)
Remove it and test resistance on terminals while blowing into the tube.
There is another pressure sensor on a hose attached to the waste assembly but appeared to be working correctly.
Posted on Apr 21, 2009
SOURCE: when I select start on my FDW60 the pump starts running but no water is coming in to the machine. After about 10 seconds the eco light starts to flash. Meanwhile the pump continues to run but no water
first make sure you have water going in , then if you d have water the next thing the water valve needs to be located , it will have a hose going into it and a hose coming out of it and two wires on it , when the dial is set to fill with water you should have 120 voilts on the two wires , if you hve th epoawer then the water valve is not workingthis is a easy fix and cheep aso same valve is used on washers , get back to me after you have done some more research
Posted on Dec 06, 2011
Tips for a great answer:
Dec 08, 2016 | Kenmore Washing Machines
Oct 26, 2014 | Televison & Video
Jun 12, 2008 | Computers & Internet
May 05, 2008 | Frigidaire Washing Machines
Jun 22, 2007 | Hotpoint 24 in. FDW60 Free-standing...
Dec 30, 2006 | BenQ FP71E 17" LCD Monitor
12,189 people viewed this question
Usually answered in minutes!