Question about Whirlpool LGB6300 Gas Dryer

1 Answer

Replacing a belt - Whirlpool LGB6300 Gas Dryer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Whirlpool Master
  • 8,220 Answers

It is the same as an electric model as shown here:

Dryer tune up

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Posted on Sep 05, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing the timing belt on a 2000 Nissan Quest/ Instructions Needed


Charles,your engine is a interference one,and you may have damaged it or ruined it,here's a link on replacing the belt. Damage to the valves and/or pistons may resulted from belt breakage.

Nov 20, 2013 | 2000 Nissan Quest

1 Answer

Replacing belt


Possible solution- warm belt with hair dryer or shrink-
wrap gun, then try stretching/ pulling over target device. Hope it helps...good luck!

May 29, 2013 | Sunny Health & Fitness Crazy Fit Massage

1 Answer

My serpentine belt went how do i change the belt do i need a special tool


Identify which belts need to be replaced. If you are replacing the air conditioner belt, you may need to remove the alternator belt because of the way the belts are shared on the crankshaft pulley. As a result, some mechanics recommend replacing both belts together.
  • Step 2 Loosen the lock bolt for the belt you are replacing using owner's documentation. The lock bolt will be near the belt tensioner component.
  • Step 3 Turn the adjustment bolt to change tension on the belt. When the belt is loose enough, slip it off.
  • Step 4 Use your memory or a belt routing diagram to install the new belt on all pulleys.
  • Step 5 Adjust the adjustment bolt to replace tension on the belt. Tighten the lock bolt.
  • Step 6 Make sure the belt is correctly seated on all pulleys and that the ribs fit into grooves on the pulleys.
  • Step 7 Run the engine and check for any flapping or looseness that could indicate incorrect installation.
  • This was copied from the service manual.
  • Jan 24, 2010 | 1995 Dodge Intrepid

    1 Answer

    Replacing belt but brush does not turn


    Are you sure that you have the right size of belt? This is the correct belt:

    Riccar 8850 Belt

    Dec 16, 2009 | Riccar 8850 Vacuum

    2 Answers

    How do I tighten the A/C belt on my 2008 Mazda 5? The darn thing is squealing so loud but I can't seem to find a tensioner anywhere...


    If it is a serpentine belt is is self adjusting. So if it is squealing then it needs replacing as it is worn out. And also possibly the tensioner needs replacing as it may not be holding sufficient tension on the belt. If it is a drive belt it more than likely still needs replacing as it will have become glazed from slipping. On a drive belt it is adjusted by loosening the mounting bracket on the A/C and moving it in a direction that tightens the belt.

    Nov 07, 2009 | 2008 Mazda MAZDA5

    1 Answer

    Belt slipping / takes a minute to start tumbling


    Before replacing belt check the space between the drum and the front AND rear seals with your fingers for foreign objects caught there. This may make the drum too tight to turn. Belt is usually broken before it needs replacing.

    Also check idler pulley next to motor and motor itself with belt off both pulleys making sure they both turn freely. I think something is binding. Check all those BEFORE replacing belt.

    Disconnect plug before opening unit.

    Aug 21, 2009 | Maytag Dryers

    1 Answer

    How do I set the timing when replacing the timing belt.


    If you are just replacing the belt because it's worn. Carefully remove the old belt and replace. no timing will be neccesary

    Mar 16, 2009 | 1997 Ford Escort

    2 Answers

    I need instructions on replacing the timing belt


    1. Remove the Alternator Belt.
    2. Remove the Water Pump Pulley
    3. Remove the Air Conditioner Belt and Power Steering Belt.
    4. Remove the Crankshaft Pulley.
    5. Remove the timing belt cover
    6. Remove the timing belt tensioner pulley.
    7. Remove the Timing Belt.
    8. (If Replacing) Remove Idler Pulley.
    Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

    I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

    Nov 10, 2008 | 2004 Hyundai Tiburon

    2 Answers

    Cam belt change on 1.3 accent


    REPLACING THE BELT AND ANY WORN PARTS WILL BE ALL THAT IS NEEDED

    Aug 12, 2008 | 2001 Hyundai Accent

    Not finding what you are looking for?
    Whirlpool LGB6300 Gas Dryer Logo

    Related Topics:

    33 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Whirlpool Dryers Experts

    Craig Butler
    Craig Butler

    Level 3 Expert

    1730 Answers

    Marvin
    Marvin

    Level 3 Expert

    85161 Answers

    Smitty

    Level 1 Expert

    240 Answers

    Are you a Whirlpool Dryer Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...