Replaced batteries and door beeps all the time

If the tv was on when you unhooked it there is a cooling fan that didn't get to cool off the picture box and it has overheated and you will have to replace the box you can order it off of eBay it takes a few moments to replace it if you still have your owners manual it will tell you all about the lights on the front of your tv I've had to change mine out a few times hope this helps Merry Christmas

On the back of the garage door opener there is a red button. Depress this button and sync your keypad to the opener. This will re-establish the code and reset the remote.

The TV has gone into "protect mode" and the flashing light is indicating a error code, TV will need a service call. Good luck and Merry Christmas!

You need to locate the rear door hatch switch and free it up or replace it if that is not an option.Merry Christmas and good luck!

Hi
In sony tv`s the 4 blink code(sony error codes)usually means that there is a vertical deflection problem.
It is often caused by a faulty vertical output i.c and/or related components. If you feel handy with a soldering iron let me know and i`ll help you with it.
Hope this help Merry Christmas

Here's what you do... This is for the trio christmas tree light show.
What you need.... small precision pointing tool.
On the largest tree base electrical box there is a push button. Press and release that button. A red led will flash indicating the box is in sync mode. turn the remote on and on the back of your remort, there is a small hole with the words reset over the top of it. Using the small precision pointing tool, press the recessed button and release. The remote will sync to the base unit. Walla!! Merry Christmas to all!!!

HI, your power supply unit has failed. you will need to replace this power supply unit asap to restore normal functions.

I would invest in some cooling enhancement in the future to prevent this type of failure.

The operating instructions on the ES20 as per the crappy manual:

Open safe using emergency key provided

Insert batteries in the box inside the door

Opening the safe
a. pre-set factory code 159
b. input 159 (the yellow light will flash and the buzzer will beep), then press B or A button, the green light will be on, rotate the knob clockwise, pull outwards, the door is opened

Closing the safe: close the door, input the code (the green light will flash for 5 secs). Turn the knob anti clockwise, the control system will activate and the safe will be locked

Changing the code: open the safe, press the red button located inside the door, the yellow light will go on indicating the code can be changed. Input the new code (1-8 digits), then press A or B button, it shall be confirmed by two beeps indicating the new code has been accepted and stored. If the yellow light and buzzer beeps 3 times the code is invalid - try again

Emergency Key - store in secure place NOT inside the safe. Remove the override cover in the centre of the face of Safe (its a silver plastic panel with Sandleford Electronic Safe ES20 on it), insert override key (a cyclinder key) - hidden underneath the override cover panel - and turn anti clockwise, rotate the knob clockwise to open door

Changing the Battery - If the red and green light are on this indicates that the batteries are low and require changing. To ensure the batteries have been installed correctly test before closing the door

References:
1. Operating instructions EA Electronic Safe
2. http://www.secustar.com/products-en/estype-safe.htm

if this thing happens then that means your hdd is already corrupted.buy new hdd and replace it.that solves the problem

I bought one myself, I have a Vista OS, non-integrated bluetooth laptop.. I had to pop in the USB dongle for capabilities....Still cant get the Mic to work though...so if anyone knows anything on that....I went to HP live chat session too.

BUT HERES THE MODES YOU MAY NEED TO PUT IT IN...
Searchable/Discovery- Hold down the power button about 6-7 secs and it will sound a few short low beeps and flash between Red and Blue, then search 8)
Erase Pairing Profiles- Press and hold the Track forward/track backward Button together until it flashes purple.
Hardware reset- if headset is screwy, froze up, LED display is incorrect...Plug in headset, and hold down bothh Volume buttons, this will power it down and reset its state of confusion, lol
Passkey is always '0000' by default
2-short Hi beeps....Connected
2- short low beeps....pairing mode also
1 long Hi beep.....Power On/Off
1 long low beep....lost Connection

Hope that helps... merry christmas