How do i use it with another username and password for my ISP Provider that not BT

The only time you don't need a user name and password to connect to your broadband/adsl company is if they supply your phone/internet/tv by cable rather than by the telephone line. If this is the case, you would have a modem supplied by the company and you would simply plug your pc/router into this.

If your internet comes down your phone line, you would normally need a user name and password. Only they can tell you what it is.

POPE configuration is logs into your ADSL system and connects to your ISP provider server to link , so one of the reason why it dosent is due to either password and username not correct. Log unto IP address of your Router and go to WAN configuration , Check your username and password and reset to the initial password and username your ISP provider gave you , when you signed up with them. Then apply changes , off your router for 1 min and then power it , then wait for the ADSL light on the router to be stable , connect to the IP address of your router again and "Volla" , it should be fine , if not , contact your ISP provider....

Usually the username and password for this are : admin for username and admin also for password. Sometimes the pasword is 1234. If someone change the password then you can hard reset the adsl modem by pressing and holding a small hole ( usually on the side, its in the manual ) using a pen or a pin. Then the username and password will be in its default. Just check the manual. Sometimes the username and password is also written in the box or underneath the adsl modem. If this does not work, you can try calling your ISP.

With a DSL modem in the US, you need to confiugre the router for PPPOE with the username/password that was provided to you by your ISP. If you can't remember the name or password, contact your ISP

WHAT ROUTER/MODEM ARE YOU USING? IF THE DSL/ADSL/LINE LIGHT DOES NOT GO SOLID THEN IT CANT SEE THE BROADBAND ON THE LINE, SO BASIC CHECKS ARE NEEDED M/FILTERS AT EVERY POINT OF THE LINE.

who is your broadband provider? Is this cable or DSL connection? Setting up the router is done via http://192.168.1.1. Leave username blank, password is admin. If you have Cable ISP, then make sure you have "Automatic Configuration-DHCP" selected and MAC address Clone is enabled on Setup > MAC address Clone (click Clone, and Apply). If it's a DSL connection and your broadband provider gave you a username and password, select "PPPoE" for Internet Connecton Type, and enter in your DSL username and password. Next verify if your modem is communicating with the router by going to the Status page and by verifying that you have an Internet IP address. If none, wait for a few minutes and power cycle your modem and router.

check you have typed in the correct password and username for your isp adsl connection

Unplug the plug (from phoneline) on back of USB modem, plug into Zoom router. Plug one end of an ethernet cable into router and one end into your PC. Type http://10.0.0.2 into a web browser (eg. Firefox or Internet explorer) username/password is admin/zoomadsl go to basic setup and input your ISP username and password (the one given to you by your internet provider) under PPP. Click configure my connection. Save changes and then write to flash (both buttons on bottom of page)

If the setup CD is unable to setup your modem/router (it is also called a "gateway") you can do the router configuration via the Web User Interface of the router. you will need ADSL settings such as:
a. Encapsulation mode. (typically PPPoA or PPPoE)
b. Multiplexing: (it can be LLC or VC)
c. Virtual Circuit Range.
d. Username & Password (ADSL UN/PW)

note: All of these ADSL settings should be provided/given to you by your ISP/ADSL provider. You can call your ISP for this settings.

just notify me if you will need further assistance doing this, but first make sure you have all the settings for ADSL.

you need

• you need a phone line that is active for dial up,or non active for naked adsl
• you need a dial up modem if you want dial up, adsl modem for broadband
• sign up with an ISP (monthly cost) and obtain user name and password
• enter user name and password (generaly via ISP cd) into (adsl)modem or setup dial up connection in windows
• wait for ISP to notify you the line has been activated, for adsl, not dial up.

all should be good

good luck
Terry