Question about Nostalgia Electrics KPM-508 Popcorn Maker

1 Answer

Will not heat up and pop - Nostalgia Electrics KPM-508 Popcorn Maker

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,220 Answers

Your power cord I would follow into the machine and hunt for a broken wire or a blown fuse possibly. Most pop corn makers are just about like a coffee pot. They have a klixon to control the temp and a couple of bullet fuses in line to prevent over heating. All of which is loacted on the base of the kettle. I wish I could be there to help ya get that popcorn popper working. Feetball season is nearly upon us.
Contact the makers

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Posted on Aug 05, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Popcorn doesn't pop to full size. The problem is, the popcorn pops however the sise of the opoed corn is only one quater the sise it should be.


Not enough heat in the kettle to do the job. The corn will dry out and pop poorly when there is not enough heat. Either a thermostat adjustment or replacement or a bad element.

Feb 01, 2014 | Cretors Kitchen Appliances - Others

1 Answer

We Have a GE Model JVM 3670BF001 Spacemaker that started making a buzzing noise periodically when turned on. After a few times of buzzing it quit heating.


You probably had a bad connection now with pop probably separated. You may also have a bad thermal over heat device. one brand is Thermodisk. But you need to know what you are doing. Might be time to replace.

Oct 18, 2012 | General Electric JVM3670BF GE Profile 36"...

1 Answer

Hayward MILIVOLT H300 BANGING AND POPPING. STILL HEATS BANGING AND POPPING QUITS WHEN HEATING STOPS.


Hi,
There are two things that can cause this...
low water flow
mineral build up in heat exchanger

Check and verify water flow through the heater

if that is ok, then the heat exchanger needs to be cleaned

heatman101

Sep 25, 2011 | Hayward H-series Electronic Gas Pool...

1 Answer

GE spacesaver microwave JVM1631WB002- making popping noise


The material is popping as a result of being heated.

Jan 19, 2018 | GE Microwave Ovens

1 Answer

Ge spacemaker xl 1800 - no heat


HI, the loud popping noise was the Magnetron tube. this is the main heating device. the noise filter is also damaged and, should be replaced as well.

In conclusion, replacing the Magnetron tube and noise filter will fix this unit.

Jun 16, 2009 | GE Spacemaker JVM1640SJ Microwave Oven

1 Answer

Loud pop and microwave doesn't heat anymore


I have a GE Profile Spacemaker model JVM3670WF001, purchased I think in 2003. Pop sound, no Heat. Light goes on, carousel goes around,
Repair or new microwave

Jun 03, 2009 | GE Profile Spacemaker Over-the-Range...

1 Answer

Microwave will not function properly.


The cavity thermal fuse may have failed. It is located on the top of the cavity.

Jun 13, 2008 | Microwave Ovens

2 Answers

Popping plate not heating up


Remember the strirring rod connects to the motor, but the heating element connects via the two prongs in the rear, so the motor can run without the heating element turned on (turn on the base without the plate on...the motor runs fine). Try reattaching the plate...it needs a good connection to the connectors in the back. It should heat up pretty quickly. Also, if you put the heating pad in the dishwasher, make sure it is dry and that the contacts aren't tarnished.

I'm certain over time the contacts will get loose and the popper will stop working, but our is going fine after a year.

Also, be careful not to drop the base...lots of cheap, hard plastic that will break and rattle around.

Mar 01, 2008 | Cuisinart CPM-800 Popcorn Maker

1 Answer

Oven shuts off


It possibly incompatible heating element installed on the oven that's why it pops up when you try to turn on and heat it..

Feb 24, 2008 | Frigidaire FEF336BC Electric Kitchen Range

Not finding what you are looking for?
Nostalgia Electrics KPM-508 Popcorn Maker Logo

336 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nostalgia Electrics Kitchen Appliances - Others Experts

Anthony Ward
Anthony Ward

Level 2 Expert

396 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you a Nostalgia Electrics Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...