Maytag washer giving error code A0

Diagnostic mode for Kenmore Elite He3t model 110 42926 ...

iFixit https://www.ifixit.com > Answers > View > Diagnostic...
Apr 8, 2016 - With the washer empty, close the door. · Push "control/on" or "Start" · Select "Drain/Spin" · Select "No Spin" by pressing SPIN SPEED touchpad.
3 answers · 2 votes: I believe this is very similar to the model I have. Here is what I did to run a diagnostic. ...
F11 error code during Diagnostic test? - Kenmore ...
1 answer
Jan 18, 2016
SOLVED: F11 code error on Kenmore HE3 - iFixit
16 answers
Mar 3, 2011
SOLVED: f h error code - Kenmore Elite HE3 ...
9 answers
Feb 21, 2012
It seems like the washer has no power - Kenmore Elite ...
6 answers
Nov 2, 2017
More results from www.ifixit.com

Diagnostic Test; Starting The Test Mode; Test Program ...

ManualsLib https://www.manualslib.com > ... > User manual
Close the door. Select the DRAIN/SPIN cycle. Select NO SPIN by pressing the SPIN SELECT button five (5) times. Push Prewash Option button four (4)times within ...

..

Maytag Bravos MTW6600T Top Load Washer Run ... - Fixya

www.fixya.com > ... > Maytag Bravos MTW6600T Top Load Washer

Maytag Bravos MTW6600T Top Load Washer, run diagnostic test cycle related issues. Get free help, solutions & advice from top Maytag experts.

Maytag Bravos MTW6600T Top Load Washer Run ... - Fixya

www.fixya.com > ... > Maytag Bravos MTW6600T Top Load Washer

Maytag Bravos MTW6600T Top Load Washer, run diagnostic test ccu related issues. Get free help, solutions & advice from top Maytag experts.

Maytag Bravos MTW6600T Top Load Washer Diagnostic ...

I had a Centennial washer on a service call doing this just the other day... After putting it trough diagnostics I found no errors and all the washer's mechanics tested okay. After resetting the control by putting it trough the diagnostics mode it continued to repeat cycles without restarting the washer.

• Try running it through diagnostics and see what error codes are in the memory. (Guide is linked below)
• What are the codes? do they give any more clues?
• clear the codes and run a test cycle.
• does it work?
• if it checks out properly with the diagnostics it's probably a bad control board...

Maytag Centennial Washer Diagnostic Guide
If it does turn out to be the control try contacting Maytag (Whirlpool) for a parts concession... Whirlpool customer service guide is linked below.
Hope that helps! Good luck!

Suggestion: Unplug washer from mains. Open up the machine, disconnect and refit all connectors with wires one by one. Could be some loose connection somewhere. Also helps in the long run

Click if helped.

Does it give an error code? What is your mod # ?

Unplug the washer. Then plug it back in and press the button that turns it off. This should unlock the door. Same thing happened on mine and there was a kink in the drain hose. Once I unkinked the hose, unplugged it, plugged it back in, turned it off, then I was able to run a drain & spin cycle to get the water out of the load that was in the washer. I then ran a full wash cycle (they'd gotten stuck in the first drain & spin cycle of a wash) and everything seems to be fine now.

How to run a diagnostic test:

1. Unplug power cord, then wait 30 seconds.
2. After plugging in, follow these instructions...

To Enter SERVICE MODE: Press Signal-Delay-5ignal-Delay (within 30 seconds of plugging in washer).
To Exit SERVICE MODE: Repeat Signal-Delay-Signal-Delay.

Here are the possible tests to run (TEST LIST). The error codes from t02 will probably be the best indicator of your problem. (scroll down to bottom to see what each command button does once you are in test mode)

• "t01"
  Model ID
  Verifies (or sets on new board) the proper Model id
• "t02"
  Error Codes
  Lists up to 10 control-detected problems
• "t03"
  Software ID
  Verifies using latest Control-eePROM-lnverter software
• "t04"
  Exercise lCD/lEDs
  Verifies that all the displays and buttons work
• "tOS"
  Pump Test
  Tests drain-out pump
• "t06"
  Pressure Switch Test
  Fills to all 3 levels, then pumps out water
• "tOT'
  ThermistorlHeater Test
  Verifies that both the Thermistor and Heater work
• "t10"
  Tumble Test
  Verifies Washer Tumbles (I.e. Wash cycle)
• "t11"
  Spin Test
  Verifies Washer spins
• "t12"
  Dispenser Test
  Verifies Dispenser fill works-for all four fill modes
• "t13"
  EOl Test
  Performs End-of-Line test sequence

Button Commands (based upon test mode)
-----------------------------------------------------------------
t01 prerequisites: none

Start Displays defined Model id (01-04); displays "---" if new board (to set Model id, rotate knob unlil desired id [01-04] displayed, press and hold "START' key to program desired model)
Power Returns to "t01"
------------------------------------------------------------------
t02 prerequisites: none

Start Displays most recent error code (EOO=none)
Start Displays previous error code (up to previous 10)
Hold start Clear all error codes (and then displays EOO)
Power Returns to "102"
------------------------------------------------------------------
t03 prerequisites: none

Start Alternate "cod" and Control Software version
Start Alternate "EE" and eePROM version
Start Alternale "Inv" and Inverter Software version
Power Returns to "103"
------------------------------------------------------------------
t04 prerequisites: none

Start loops on lighting lED's, LCD and cycle ids
Any button Beeps when depressed
Power Returns to "t04"
------------------------------------------------------------------
tOS prerequisites: none

Start Displays "P" and pump for 60 seconds
Power Returns to "t05"
------------------------------------------------------------------
t06 prerequisites: none

Start Displays "E" (for Empty) and starts filling when reaches Foam level-displays "F"
Start Fill, when reaches Main level-displays "nl"
Start Fill, when reaches overflow leve~ displays "OF," pumps out, displays "E" when tub empty
Power Returns to "t06"
------------------------------------------------------------------
t07 prerequisites: Main level pressure switch must work

Start Displays temperature in OF, fills to main level, turns on heater up to 5 minutes, displaying rising temperature
Power Pumps out water and returns to ''t07''
------------------------------------------------------------------
t10 prerequisites: none

Start Displays "It" and tumbles tub alternating the direction every 5 seconds
Power Stops tumbling and returns to "t10"
------------------------------------------------------------------
t11 prerequisites: none

Start Spins to 400 RPM displaying increasing RPM
Start Spins to 1100 RPM [Greater than or equal to 1000, displays "Axx"; Greater than or equal to 1100, displays "bxx" (xx, 0 to 99)] [currently error-automatically goes to 0 RPM]
Power Stops spinning and returns to "t11" when stops
------------------------------------------------------------------
t12 prerequisites: none

Start Displays "pdt" and fills via pre-wash chamber
Start Displays "ddt" and fills via main wash chamber
Start Displays "bdl" and fills via bleach chamber
Start Displays "Fdt" and fills via fabric softener chamber (stops if reaches Main level during any fill)
Power Pumps out water and returns to "t12"
------------------------------------------------------------------
t13 prerequisites: none

Start Starts EOl test sequence (NOT used in Repair)
Power Returns to ''t13''

Once you have the diagnostic codes, check this post for the meaning of the codes:

http://www.fixya.com/support/t9556917-ge_model_wcvh6800j_error_code_04

Hi


Thanks for using FixYa. Error NF means No Fill. The washer has tried to fill but was unsuccessful. NF indicates No Flow. There is something that is interrupting the inbound flow of water to the washer, either hot or cold. Sometimes this happens when water service in the area is interrupted, creating an air pocket that causing the water valve not to sense water.

Try running the diagnostic test by—

• Press the delicates and heavy soil keys together for 3 seconds.
• You are in the service mode.
• Now, press wrinkle free key, cold water should start entering.
• Then, press the cotton sturdy and hot water should flow.
• To exit the test mode, either unplug the machine or press the delicate and heavy soil again for 3 seconds.

Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Keypad/User Interface Failure

F then 2 flashes when in:
Diagnostics Test mode if a stuck key is detected.
Standby mode if there is a user interface mismatch.
DISPLAY (Saved Code) EXPLANATION AND RECOMMENDED PROCEDURE

Console and Indicators
This test is performed when any of the following situations occurs during the Console and Indicators Diagnostic Test:


None of the indicators light up No beep sound is heard Some buttons do not light indicators None of the indicators light up:
1. Perform steps in Accessing & Removing the Electronic Assemblies, and visually check that the P11 connector is inserted all the way into the machine/motor control.
2. Visually check that the user interface assembly is properly inserted in the console assembly
3. If both visual checks pass, replace the user interface assembly.
4. Plug in washer or reconnect power.
5. Activate the Console and Indicators Diagnostic Test mode to verify repair.
6. If indicators still do not light, the machine/ motor control has failed: Unplug washer or disconnect power. Replace the machine/motor control assembly.
Plug in washer or reconnect power. Activate the Console and Indicators Diagnostic Test mode to verify repair.

No beep sound is heard:
1. Perform steps in Accessing & Removing the Electronic Assemblies, and visually check that the P5 connector is inserted all the way into the machine/motor control. If visual check passes, replace the user interface assembly.
2. Plug in washer or reconnect power.
3. Activate the Console and Indicators Diagnostic Test mode to verify repair.
4. If replacing the user interface assembly failed: Unplug washer or disconnect power. Replace the machine/motor control assembly. Plug in washer or reconnect power. Activate the Console and Indicators Diagnostic Test mode to verify repair.


Some buttons do not light indicators:
1. Perform steps in Accessing & Removing the Electronic Assemblies, and visually check that the console electronics and housing assembly is properly inserted
into the front console. If visual check passes, replace the user interface assembly.
2. Plug in washer or reconnect power.
3. Activate the Console and Indicators Diagnostic Test mode to verify repair.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

motor control possibly bad