Question about Health & Beauty

1 Answer

I have a IZIP I200 scooter I replaced the batteries and still does not woork

I repalce the batteries and still does not work what cna ido?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 60 Answers

Although your device isn't a mobility scooter, they share many similarities. The following info should be of help to you

If when switched on you don't get lights you are not getting any power to the tiller head, the meter should be reading voltage regardless of the condition of the control circuitry. My first scooter was a very old AMIGO, it sat in a barn for 20 yrs, this was anything but a dry environment.As a matter of fact i has to a power washer to clean the two inches of Chicken manure off it. This scooter was so old that it has an discrete component open controller board as opposed to fully potted and enclosed LSI based controllers we see on todays scooters. The engager in the tiller was oxidized, and had to be cleaned and dried out. I rinse the controller out with distilled water then put it in a preheated oven at 150 F for 24 hrs. WARNING make sure of the temperature some ovens will not go this low. The newer controllers are potted and enclosed, making them water resistant, they use LSI which are proprietary and can't be purchased or repaired. I liked older controllers because you could fix them.

What you got to do is what we call "chase the voltage" First you will need a 24v circuit tester
http://www.amazon.com/OEM-25886-6-24V-Circuit-Tester/dp/B0014WIVX6

You may also need a VOM meter only $9
http://www.amazon.com/Mastech-YG188-Pocket-size-analog-multimeter/dp/B00064CH6A/ref=sr_1_8?s=hi&ie=UTF8&qid=1339024102&sr=1-8

The problem is 24volts is either not getting to the tiller head or you have a broken wire in the tiller head. Start at the headlight make sure its switched on. Use the circuit tester, put the clamp to ground, use the probe to find the 24volts, The hot side is the side wired in series with the switch. The tester will light up when it has voltage. Chase the wire back through the system. When you get to a cable or anywhere you can't see the wires use the VOM meter, disconnect the scooters batteries leaving the power switch on. Set the meter to read resistance scale high scale, short the probes together, zero the meter. Put one probe at the headlight the other probe at the connector you think the wire ends up at. Normally every wire is a different combination of colors like red; with a white stripe. Most of the time a wire ends up at a connector and the color code doesn't change. So if you are not getting continuity on any of the pins on the connector you know its got to go, you've isolated the open circuit too the tiler head. Here's a test you can run! Turn headlight on, power on for scooter, disconnect scooter battery, place one probe at head light. Disconnect tiller cable. Probe each pin, one of them hast to cause the meter to deflect to zero. If if doesn't the problem is in the tiller head. When working with little wires i like to use crochet needles. You can use the meter to check cables each pin in must have a pin out. If you don't get continuity between pins the cable is bad toss it.

Posted on Jul 17, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Battery won't stay charged and has been repalced twice since October


hi, you replaced the batteries twice? using the same charger, have you tried another charger ?, okay let me tell you about mobility scooter chargers, it quite complex but some chargers will charge your new batteries correctly due to resistance etc, it more complex than this however now as your batteries get older your charger maybe having a problem charging your batteries , not because they faulty, now this is due to internal resistance once again the batteries problem reappears within 3 to 6 six months , it could be just the batteries are not good enough , I have seen a whole combination of faults , please bear in mind there are some dodgy batteries out on the market....


so


1. first try another charger

Regards

Jan 19, 2013 | Pride Mobility Go-Go Ultra X 4 Wheel...

1 Answer

Amigo handicap scooter -- loosing distance with in use


you'll need new batteries plan on replacing them at 1-1/2 to 2 years

Oct 14, 2012 | Amigo Health & Beauty

1 Answer

I need a manual for an izip 200 electric scooter


Google it with make ,model, and manual LUCK

Oct 29, 2010 | Toys

1 Answer

Install battery


First make sure the scooter is off.
Unscrew and take off the deck
Unplug and remove the old battery pack
Put the new battery pack in and plug it in, using the same connection as the old batteries pack.
Screw the deck on and your done!
Oh, and make sure you give the battery a good charge(the full charging time). The first charge of a battery is the most important one.

May 16, 2010 | Mongoose Currie Schwinn Gt Izip Scooters

3 Answers

Manual for Schwinn Mongoose z350 electric scooter


My Mongoose z350 electric scooter goes from full charge to empty in about 20 seconds. I can turn it off and back on and it shows a full charge every time. What is going on with it?

Mar 24, 2010 | Mongoose Currie Schwinn Gt Izip Scooters

2 Answers

I need to assembly the wiring for the batteries. what is the method for connecting the 2 positive and 2 negative terminals?i have the schwinn S350 scooter.


Scooter positive terminal to battery 1 positive. Scooter negative to battery 2 negative. Battery 1 negative to battery 2 positive.

Jan 28, 2010 | Mongoose Currie Schwinn Gt Izip Scooters

1 Answer

Mongoose Pro Scooter will not go


you can have the battery tested for its voltage with an voltage meter and see if it is giving enough output for its purpose, but from the sounds of what you are saying it seems the battery isnt holding enough to power the scooter

Sep 03, 2009 | Mongoose Currie Schwinn Gt Izip Scooters

4 Answers

Schwinn S350 Scooter batteries


Schwinn batteries can be found on amazon, click here and take a look: Amazon com Schwinn S350 Scooter batteries. I hope this was helpful. Cheers

Aug 02, 2009 | Mongoose Currie Schwinn Gt Izip Scooters

1 Answer

Schwin scooter not running properly


If the battery is old its likely that it needs to be replaced. Also, if batteries sit in the cold in the winter or are exposed to high heat they can be damaged. Try checking out http://www.batteryinternational.com/electric-scooter-batteries.html for a scooter replacement battery.

Jun 09, 2009 | Mongoose Currie Schwinn Gt Izip Scooters

1 Answer

Schwinn S1000 illuminates both green & red light, but no power


I am having the same problem. By all indications it looks like the motor controller is the problem. Everything else works OK. I am pulling the controller tomorrow and replacing. If that doesn't work I am junking it.

May 12, 2009 | Mongoose Currie Schwinn Gt Izip Scooters

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Health & Beauty Experts

Rob Hill
Rob Hill

Level 3 Expert

1367 Answers

Marvin
Marvin

Level 3 Expert

85020 Answers

Jeff Tilburn
Jeff Tilburn

Level 3 Expert

1332 Answers

Are you a Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...