I need to remove front and back fascias of my 6500 classic

FASCIA FRONT REMOVE?

Remove the fascia (2) to splash shield screws (1).

Remove the lower fasteners (2) and disconnect the electrical connectors (1).

1. Remove the fasteners (2).
2. Separate the fascia (3) from the fender support clips (1).
3. Remove the push pin fasteners (3).
4. Remove the hood overslam bumpers (4) and remove the fascia.

It's attached to the windshield washer tank

Raise and support vehicle.

Remove wheels.

Remove plastic push pins attaching fascia to fuel tank skid plate.

Remove plastic rivets attaching fascia to wheel liner.

Remove nuts attaching upper edge of fascia to quarter panel and wheel liner

Remove plastic push pins attaching fascia to liftgate opening

Remove screws attaching fascia to liftgate opening.

Remove D pillar trim and scuff plate outboard screws.

Remove the rearward tie down screws and the aperture trim panel.

Carefully peel back the rubber body sealer patch to access the retainer clips.

Release the forward and rearward retainer clips on both sides of the fascia.

Grasp forward edges of fascia and pull outward to disengage retainers attaching fascia to quarter panel

Separate fascia from vehicle

Hello Bruce...here are the steps to follow per All Data.

Release hood latch and open hood.
Remove the headlamp assemblies.
Hoist vehicle and support with safety stands.
Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
Remove front wheels.
Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
Disconnect fog lamp wire connectors, if necessary.
Lower vehicle.
Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
Remove bumper fascia from vehicle.
INSTALLATION

Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
Hoist vehicle and support with safety stands.
Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
Install front wheelhouse splash shields fasteners.
Install front wheels.
Connect fog lamp wire connectors, if necessary.
Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
Lower the vehicle.
Install the headlamp assemblies.

The "push pin fasteners" are the pain you are having i believe. They push in, but to get them out you need squeeze them on the back & pull at the same time. If you happen to break a few, you can buy them in various sizes at the auto parts store. I hope this information is helpful, an owners manual will not have any info like this in it.

Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

1. Release hood latch and open hood.
2. Remove the headlamp assemblies.
3. Hoist vehicle and support with safety stands.
4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
5. Remove front wheels.
6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.

Fig. 1
Fig. 2

1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
2. Disconnect fog lamp wire connectors, if necessary.
3. Lower vehicle.
4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
5. Remove bumper fascia from vehicle.

INSTALLATION

1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
3. Hoist vehicle and support with safety stands.
4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
5. Install front wheelhouse splash shields fasteners.
6. Install front wheels.
7. Connect fog lamp wire connectors, if necessary.
8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
9. Lower the vehicle.
10. Install the headlamp assemblies.

Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.

• Remove the front fascia extensions, if equipped.
  
• Remove the front fender liners.
  
• Remove the fog lamps.
  
• Remove the bolts (4) from the front bumper fascia (3) at the fender.
  

Remove the bolts from the front bumper fascia at the fender

Remove the push-in retainers (2) from the bumper fascia using J38778.

Remove the fascia bolts (1) from the fascia.

Remove the fascia from the vehicle.

Remove the 3 bolts which secure the composite headlamp.

Remove the 3 bolts which secure the composite headlamp

1. Remove the sidemarker bulb electrical connector.
   
2. Remove the sidemarker bulb, if necessary.
   
3. Remove the composite headlamp assembly from vehicle.
   

To install:

1. Install the sidemarker bulb to the composite headlamp, if removed.
   
2. Connect the sidemarker bulb electrical connector.
   
3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
   
4. Install the front fascia.
   
5. Install the headlamp bulb to the composite headlamp, if removed.
   
6. Fasten the headlamp bulb retainer clip.
   
7. Install the socket to the headlamp bulb.
   
8. Install the rubber cover to the composite headlamp.
   
9. Aim the headlamps.
   
10. Close the hood.
    

The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.

1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
3. You will also need to remove some of the fasteners at the front of the inner wheel well.
4. The Front Bumper Fascia is the plastic cover over your front bumper.
   
5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.
   

hello. below is the procedure for removal of the headlamp for bulb replacement. to access the headlamp you will need to remove the bumper fascia. http://gsi.xw.gm.com/image_en_us/gif/000/001/725/1725371.gif Callout Component Name 1 Front Compartment Sight Shield Plastic Retainers (Qty: 6) 2 Front Compartment Sight Shields (Qty: 3) Tip Each front compartment sight shield is serviced separately as needed for repairs http://gsi.xw.gm.com/image_en_us/gif/000/001/728/1728611.gif Callout Component Name Preliminary Procedure Remove the front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement . 1 Front Fascia Extension Plastic Retainers (Qty: 5) 2 Front Fascia Extension http://gsi.xw.gm.com/image_en_us/gif/000/001/733/1733942.gif Callout Component Name Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedures Remove the front compartment sight shields. Remove both front bumper fascia extensions. 1 Front Bumper Fascia Reinforcement Nut (Qty: 2) Tighten 6 N·m (53 lb in) 2 Front Bumper Fascia http://gsi.xw.gm.com/image_en_us/gif/000/001/736/1736893.gif Callout Component Name Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedure Remove the front bumper fascia. 1 Headlamp Nut (Qty: 1) Tighten 6 N·m (53 lb in) 2 Headlamp Bolts (Qty: 3) Tighten 6 N·m (53 lb in) 3 Headlamp Assembly

You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
Tell me if this works for you?
HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
REMOVAL

1. Release hood latch and open hood.
2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
8. Remove headlamp housing Remove Headlamp Housing

INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

1. Place headlamp housing into position.
2. Connect wire connector to lamp socket(s) and/or bulbs.
3. Verify headlamp and signal lamp operation.
4. Install jackscrews to attach headlamp housing to crossmember.
5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
7. Install nut on fascia stud through the splash shield access hole.
8. Verify headlamp operation and alignment

how do i change the front cover on a nokia 6500s?