I have the same problem, after clearing the filter, I can not reset the filter timer to 0. Could the Hitachi CP-X28 service centre help to provide solution? Thanks! I have the same problem, after clearing the filter, I can not reset the filter timer to 0. Could the Hitachi CP-X28 service centre help to provide solution? Thanks!
I also have the same proble. After looking through user manual, there is no description about such a warning message.I also have the same proble. After looking through user manual, there is no description about such a warning message.
I have the same problem with the Hitachi CP S210. It is telling me that I need to reset the filter timer. Are the directions that you gave the same for the projector that I have? I am not able to check it at this time or I would just see for myself. Hope that you can help. Thanks. I have the same problem with the Hitachi CP S210. It is telling me that I need to reset the filter timer. Are the directions that you gave the same for the projector that I have? I am not able to check it at this time or I would just see for myself. Hope that you can help. Thanks.
You can't post conmments that contain an email address.
Reset the filter timer.
(1) Turn on the projector. While the projector running, press the MENU button to
open the menu.
(2) Choose the “OPTION” on the menu using the up/down button, then press the right
button or ENTER button.
(3) Choose the “FILTER TIME” using the up/down button, then press and hold the right
button of projector or the RESET button of remote control for 3 seconds.
(4) Choose the “RESET” using the up button.
Go to Advanced Menu, then Options menu. Go to Filter time and hold the reset button for 3 seconds. This will bring up a sub menu and use the up arrow to reset. Page 37 of the user manual
1. Chose "OPTION" on the menu 2. Chse teh "FILTER TIME", then press AND HOLD the right arrow button, or the RESET button on the remote for 3 seconds. 3. Choose the RESET option
hey to all trying to reset the annoying 'clean filter" or "change lamp" message on the hitachi cps 210 projector.
go onto filter in the menu, then hold down the little reset button on the remote botom left i think,, or right.. it will then go to zero. hold for ablut 5 seconds
that should do it..
dont try pressing reset then execute. it seems to do nothing. gotta use the remote reset button.
hope this helps. i know how annoying the message box is!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Your unspecified model of Alvatel cell phone is buggy. Try to do a Factory Reset if bug goes away. You chould look up in your manual if factory reset is available, else you caould visit the office of your Mobile Service Provider, they know how to do a Factry Reset. A warning, after factory reset you'll lose all your saved data!
You will have to take an oil pressure reading and compare to specifications. It could be that the pick up screen is plugged. Do not drive the car as damage to engine will occur.
Hello. When the water filter warning light comes on it is time to replace the water filter. Once the filter is replaced you will have to reset the warning light. To do that Hold the Lock/Unlock Button and the Water Dispensing Button for (3) Seconds. The Change Filter Light will Blink and Reset. Joe
You can try to reset the ecu, just switch the ignition into off position, disconnect the sensor cable at the fuel filter housing, turn the key into on position, but dont start your car, connect back the cable, the warning should goes off after fews second.
I had the same problem. There is an internal reset button just above the lamp that needs to be reset. You have to take the cover off, which would void your warrantee, but it's quite easy. My lamp only had 660 hrs, and I bought a new one too. So now I have an extra. My guess is that my filter was getting clogged causing an overheating situation and tripping this reset button which I'm guessing is a heat sensor.
I have the same problem, after clearing the filter, I can not reset the filter timer to 0. Could the Hitachi CP-X28 service centre help to provide solution? Thanks!
I also have the same proble. After looking through user manual, there is no description about such a warning message.
clean the air filter
I have the same problem with the Hitachi CP S210. It is telling me that I need to reset the filter timer. Are the directions that you gave the same for the projector that I have? I am not able to check it at this time or I would just see for myself. Hope that you can help. Thanks.
×