E5 error code on a YorkFitness Inspiration treadmill, anyone know what i should do?

There is a video, but I suggest that you phone York Fitness direct and ask them. Disconnecting the power is a reset.

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk0136VFWGL2jP4g3d4uHovWkKccKcw%3A1612217121584&ei=IXsYYOWNI4fj-gSO5LiYBA&q=RESET+BUTTON+YORK+FITNESS+INSPIRATION+TREADMILL+51053

..

The E5 Error is specific to the TR2000e and the TR3000e treadmills.

The error code triggers when an object is detected by the folding sensors on the underside of the treadmill. The folding sensors look like small trapezoids: two on the back and two on the front. Make sure there are no foreign objects underneath the treadmill. If no objects are present, inspect the sensors for damage. If the problem persists, please contact customer service.

What does the trouble code 70 h95 mean - Fixya

www.fixya.com/support/t25932829-trouble_code_70_h95_mean

28 mins ago - what does the trouble code 70 h95 mean - Bowflex Treadmills question.

What Does Your Treadmill's Error Code Mean? - LifeSpan

www.lifespanfitness.com/.../what-does-your-treadmills-error-code-mean

Free
May 21, 2015 - Please refer to the following table if your LifeSpan treadmill is displaying an error code. If after trying the suggested solutions your treadmill is .

Replacement Parts for Fitness Exercise Equipment at SPORTSMITH

True Treadmill Errors and Service Messages

• The True 600, 700, 725 and 750 series treadmills are equipped with built-in diagnostics and maintenance reminders that display either an error message or service message as they occur.
• The error messages that may be displayed by the built-in diagnostics are as follows:
  • E1:INCLINE
  • This means that the incline is moving when it has not been commanded to.
  • E1:MINIMUM
    • This is a minimum incline calibrating error that can be cleared by calibrating the incline.
  • E1:RANGE
    • This means the difference between the treadmills zero position and maximum incline is not sufficient.
  • E1:STALL
    • This means that the incline is not moving when it has been commanded to.
  • E2:OVERSPEED
    • This occurs when acceleration greater than 2.1 mph occurs as this is greater acceleration than anticipated.
  • E2:CAL
    • This means feedback cannot reduce or increase speed to target and error can be cleared by calibrating treadmill.
  • E3:EEPROM
    • This error happens when a data error is detected on the EEprom. The control panel needs replaced if this error occurs.
  • E5:SENSOR
    • This error occurs when there is no speed or RPM feedback detected from speed sensor.
• The service messages that may be displayed by the built-in maintenance reminders are as follows:
  • S1:LUBE
  • This service message displays when it is time for inspection of the deck lubrication system.
  • S2:CLEAN
    • This service message displays every 500 miles and is your prompt to clean the treadmill.
  • S3:MOTOR
    • This service message displays every 2500 hours and is your prompt to check the motor brushes.
• This information should help you understand the cause of the error message or code and how to take action to repair your True treadmill

Errors for True Treadmills E5 Sensor E2 Cal S1 Lube and more

Error 1: Speed sensor error Turn the power switch off and on again to reset the treadmill. If the treadmill returns to normal operation, you may continue to use the treadmill. If treadmill does not return to normal operation, then call the dealer for advice.
ERROR 1 CODE This is a safety feature that can stop the treadmill from functioning. This error can occur because the computer is not receiving the correct information from the speed sensor located near the motor. As a precaution the computer stops the treadmill until it begins to receive the correct feedback. By performing a few simple checks, the error can be cleared quickly and easily, and the treadmill can be ready for use. The treadmill does not move and displays "ERROR 1" Switch off the treadmill at the mains, and then switch it on again. If "ERROR 1" still shows switch off and push the running mat round (1 cycle) using your feet. Then switch back on. If "ERROR 1" still shows, then UNPLUG from the mains and check all of the wire connections made during the assembly. (SEE BOLD PRINT) UNPLUG If the treadmill still does not move, then please contact the helpdesk. Doing this may reset the program error, and the treadmill will be ready to use. This should reset the sensor, and the treadmill will be ready to use. Once the cables have been checked, turn on the treadmill again. This should eradicate the problem. 1. 2. 3. When assembling, there are several cables that need to be connected. It is very common for these cables to look like they are connected when they are in fact not fully connected. Make sure that these cables are connected as tightly as possible. The connections may have come apart whilst assembling the treadmill. here is a link to your treadmill web site http://www.yorkfitness.com.au/uploaded/pdf_71T520i%20Treadmill_5562.pdf

Error codes are listed on page 22 of the manual(YORK T500 TM / 22)

http://www.yorkfitness.com.au/uploaded/pdf_68T500%20Treadmill_8615.pdf

yes you must read the instruction manual for software calibration.
or open the hood motor, and read the instruction attached.
or you must call to York supply for customer service and ask them where is located in case that you will not find them.

God bless you

Dear Sir:

This error come because the power up test the sequence. The test is performed beacuse a permanently STUCK key inhibit the correct operation.

Liquida or perhaps perspiration in present on the surface of touch sensitive display. Try to remove the keypad connector cable. Restart the power is the ERROR 5 is not longer presente the keypad is the cause. If do the display housing is the problem

Run the software calibration for eay diagnose and trouble.

sincerely. God bless you.

ernesto cuadra
managua, nicaragua. c.a

Dear Sir:The power up test sequence has detected a key inthe operated condition. The power up testsequence is performed every time the unit isturned on (powered up). This test is performedbecause a permanently stuck key will inhibit thecorrect operation of the unit.
sincerely. God bless you.
ernesto cuadramanagua, nicaragua. c.a