Not switching on

Check seat switch
neutral safety switch
power to main contactor
does the contactor close?

Just understand, that the 5V supply you measure comes from the power supply is used for standby and power On switching purpose. As far as this supply voltage is OK, the fault must be to its main board, because, from the main board comes the power up start voltage back to power board to initialize its whole working.
Check the main board. The power supply regulator board is now Ok; otherwise, you can't get this 5V supply line active. Contact any service technician.
If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box and press "Enter".
http://electronicshelponline.blogspot.com/

1) Please exchange batterires for a new ones.
2) Tight the flexible cables from keypane vs display board.
3)Tight the connector from display board vs lower board(Main motor board)
4)Adjust the reed sensor switch by 1/8" or 3mmsSee the diagram attached.
5)Measure input voltage for 115 Vac to input of main motor board
6) Measure input for power supply for +5VDC to main motor board.
7)Measure output voltage for +5vdc to Display board.
8) Finally see the block diagram that I am attached that I did for people like you. For easy diagnostic and troubleshooting.
Sincerely. Merry Christmas.
Ernesto CuaddraManagua, Nicaragua.

1) Exchange batteries by new ones.

2)Tight the flexible cord Keypanel vs display board.

3) Tight the connector from display board vs lower board.
4) Adjust the sensor reed switch see the diagram by 1/8"
5)put your software calibration to work, for diagnostic and adjust.see the instruction in your owner manual y/o under hood.
6) Adjust the speed sensor and tigh the connector very well.
7)Test the main motor for 115VAC, see the plate from motor for to check the voltage.
8)See the main motor board or lower board, Test for 115 Vac, and +5VDC for output from the main controller board and display board

See the block diagram and take the diagnostic very effective. sincerely.

Merry Christmas.

ernesto cuadra
managua, nicaragua. c.a.

1) Exchange batteries for new ones.
2) Tight the flexible cable from keypanel vs display board.
3) Tight again the connector from display board to lower board or main motor board.4)adjust the sensor reed switch bby 1/8" see the diagram attached.
5)See if you test measure for +5VDC coming from power suply then main motor board and finally Display board.
6) Test the power supply form output +5VDC , and input from main motor controller board.

See the block diagram that I did for people like you, for better and undertanding diagnostic.

suggestion: Run the calibration software read the owner manual and see the steps under your hood. sincerely.Merry Christmas.

ernesto cuadra
managua, nicaragua.

1)ADJUST THE SENSOR REED SWITCH BY 1/8" SEE THE DIAGRAM
2) IF YOUR SISTEM HAS BATTERIES EXCHANGE BY NEW ONES.
3)TIGHT THE FLEXIBLE CABLE FROM THE KEYPANEL VS DISPLAY BOARD AND THEN TIGHT THE CONNECTOR FROM THE DISPLAY BOARD VS LOWER BOARD OR MAIN MOTOR CONTROLLER BOARD.
4) WILL BE A GREAT IDEA IF YOU CAN MEASURE WITH YOUR VOLTEMETER +5VDC coming from the main motor controller board to display board.
Now if there are missing the fault: is main motor controller of course after you did the first step or the voltage is there the display board is faulty.

see the block diagram how the main motor board control by 90percent of function of the any treadmill. Good luck, sincerely. G-d bless you.
E.CUADRA
MANAGUA, NICARAGUA.

It is a long drain error and occurs when the washer is not fully drained after 10 minutes of draining. Remove the cabinet cover and check the following:

1. Drain Pump Connector The connector may be disconnected or disassembled. Reassemble or repair if necessary.
2. Drain pump coil
   Check pump coil resistance between the terminals using an ohmmeter. Resistance should be between 10-20 ohms. If the resistance is too high or too low, replace the drain pump.
3. Voltage Check the voltage between the connector in step 1 during spin. The voltage should be 120Vac, else replace the main board assembly

Main board replacement:

1. Disconnect the power connector and sensor switch assembly.
2. Remove the main board protective cover.
3. Disconnect the connectors.
4. Remove the screw on the back of the main board.
   
5. Slide the main board to the right then pull it up.
6. Replace the main board in reverse order above.
   

It is a long drain error. The washer is not fully drained after 10 minutes of draining. Remove the cabinet cover and check the following:

1. Connector The connector may disconnected or disassembled. Reassemble or repair if necessary.
2. Drain pump coil
   Check pump coil resistance between the terminals using an ohmmeter. Resistance should be between 10-20 ohms. If the resistance is too high or too low, replace the drain pump.
3. Voltage Check the voltage between the connector in step 1 during spin. The voltage should be 120Vac, else replace the main board assembly

Main board replacement:

1. Disconnect the power connector and sensor switch assembly.
2. Remove the main board protective cover.
3. Disconnect the connectors.
4. Remove the screw on the back of the main board.
   
5. Slide the main board to the right then pull it up.
6. Replace the main board in reverse order above.
   

Remove the Power Supply cable to Y Main board and check the Vs voltage in Power Supply board.
1. Vs voltage is OK, replace the Logic board or Y Main board.
2. Vs voltage is NG, replace the Power Supply board.