What does a 2-3 dignostic code on a Mitsubishi 55819 mean?

When it shuts off and the green power light goes off, press both the menu and input buttons on the front of the set (not the remote) and hold both for about five seconds and release.

Power light will blink a two digit error code like 2 blinks and then 3 blinks and repeat it several times.

What is the error code?

MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device" and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix. SD TECH

To know where the problem is:

when set shuts off and green power light goes off:

On front of set press and hold both the menu and input buttons at same time for at least 5 seconds and release both buttons.

Power light will blink a two digit error code like: 2 blinks, 2 blinks, a pause and repeat it several times.

Let me know what error code you find and I will tell you what it means.

SD TECH

this model has a self check, when green light comes on and then goes off. Push and hold both the Menu and Input buttons on the front of the set for at least 5 seconds and release both.

Power light will blink a two digit error code like 2 blinks 2 blinks, a pause and then repeat it several times.

Let me know what error code you find and I will tell you what it means.


SD TECH

Please do the self check this model should have;

When power light comes on and then goes off: On the front of the set press and hold both the Menu and Input (or device) for at least five seconds and then release both buttons.

Watch the power light as it should now blink a two digit error code--for example--2 blinks, a pause and 2 blinks. It will repeat the code at least five times.

Let me know what error code you find and I will tell you what it means.

SD TECH Steve

When you turn it on and it shuts off---ON THE FRONT OF THE SET PRESS AND HOLD BOTH THE MENU AND INPUT(DEVICE) BUTTONS TOGETHER FOR AT LEAST 5 SECONDS AND RELEASE BOTH BUTTONS.

Power light should blink a two digit error code---for example: 2 blinks, a pause and 2 blinks--This is the most common error code.


Let me know what error code you get and I will tell you what it means and if 2-2 what the problem is.

If this information helped you, rate this solution as I do this here for FREE.

SD TECH

code stands for loss of vertical. I had one of these if you can check pico fuses, check the ones on the main power board the one with the 2 convergence amps if any of them are blown then most likely the convergence amps have shorted out.

ok when the power is plugged in hold down the menu + device buttens for five sec what is the error code there should be two sets of numbers....
like 1 pause 2 let me know and i'll see what i can do!

Code 22 indicates that your set is in shut down due to what is called Short Protect. The most likely cause is the Converge Ic's drawing too much current and opening one or 2 fuses. Normal repair cost varies by area and servicer. Expect 250 to 350 plus the service call. I normally do this on site.

try holding in the menu and input buttons together on the front panel for about 8 seconds to see if the self diagnosis feature will blink a two digt code then let me know what happens