Glass surface of warming zone/plate smashed.

If it is just the glass, the back plate the glass sticks to is only clipped in. You will probably need to smash the old glass when you GENTLY lever the old one out. Check the back of the plate as the heated versions have a wire connected to it. The picture is for a 2008 but the set up is exactly the same.


To replace the whole assembly you need to remove the trim and the door card. The bolts mount the housing from the inside through the door. The trim and door card will be held on with small screws and push in clips. Some of the screws can be tucked out of sight so make sure you don't miss any. The push clips should 'pop' out if GENTLY levered out.

Disconnect the power from this range! Have a qualified service person come and check it out/repair it. This is not a job for amateurs.

Hi,If you want to cut glass left over form old project or somebody gave it to you for what ever reason the first thing you need to do is make sure that the glass is plate glass becouse if you try cutting tempered glass its going to blow in your face.
Usually tempered glass has a stamp somewhere in the corner which proves that is tempered and the company that tempered it. After you know for sure that your glass is plate glass you need:

1.Safety glasses
2.Glass gloves
3.Glass cutter
4.Straight edge
5.Cutting table or flat surface covered with felt or short hair carpet
6.Measuring tape
7.Clamps (to hold your straight edge while you score the surface)

The thing is you dont cut glass,you score it with the cutter and then brake it.Please let me know what kind of glass are you going to cut so I can be more specific.

The cover plate is above the glass white surface of the scanner. If this is the same dirty stains will come out on copies.
The glass must be clean.
By feeding the original documents through the ADF, the scanner lamp is no longer the path to scan, the ADF is responsible for passing the original document over the scanner, while it remains still placed on the side under a thin glass is to a large glass side. This also must be clean, otherwise you will be black lines on each point or spot on the glass.
Good luck ...

Im not sure but their is probably a reset for the fuel pump check your owners manual and see or ask a parts store

not a train smash, locate screws to seperate the two door halves to allow access to the inner glass. remove screws and plates holding the broken glass. clean then place new one in possition and tighten screws comfortably tight.(dont over do it).Reassemble door.

here's 2003, don't have 2008

Removal
NOTE: Left-hand dual arm mirror with heat shown, non-heated and aero mirrors similar.
All exterior mirrors

1. Position the exterior mirror glass in the full down position.

1. Grasp the top and carefully pull the exterior mirror glass away from the mirror housing.

1. Disconnect the electrical terminals (if equipped) and remove the exterior mirror glass.

Power exterior mirrors

1. Remove the jack pins from the exterior mirror glass backing plate.
   • Use pliers to grasp the jack pins at the base to remove.

Installation
Power exterior mirrors

1. Remove the sealing boots from the exterior mirror motor.

1. Install the jack pins in the sealing boots.

1. Install the jack pins and sealing boots.
   1. Hold the legs of the jack pins and push the jack pins back into the exterior mirror housing.
   1. Install the sealing boots so the boot shoulder is under the mirror collar and turn each jack pin until the head of the jack pin is aligned with the slots in the sockets on the backing glass plate.

All exterior mirrors

1. Place the new exterior mirror glass assembly down on a smooth firm surface.

1. Align the friction pins vertically to the exterior mirror glass backing plate socket and push down to snap the pivot ball into the socket.

1. CAUTION: Do not over heat the exterior mirror glass backing plate. Heat only until backing plate is warm to the touch.
   Using the special tool, warm the main pivot sockets in exterior mirror glass backing plate.

1. Loosely install the glass.
   1. Connect the electrical wiring to the electrical terminals (if equipped).
   1. Position the friction pins in the mirror housing.
   1. Align the jack pin locating tabs to match with the mirror glass back.

1. Using a flat hand, press on the center of the mirror glass until seated on the center pivot of the mirror housing.
   • Press the mirror glass toward one of the jack pins until snapped in place.
   • Repeat for second jack pin.

Power exterior mirrors
NOTE: If the jack pins do not engage, they may not be aligned correctly. Remove the exterior mirror glass, align the jack pins to the slots in the sockets and repeat the installation procedure.

1. NOTE: The jack pin should click while manually adjusting the exterior mirror glass.
   Tilt the exterior mirror glass to the full outboard position and then press on the outer side of the class until the in/out jack pin snaps into the socket on the exterior mirror backing plate.

1. NOTE: The jack pin should click while manually adjusting the exterior mirror glass.
   Tilt the exterior mirror glass to the full down position and then press on the outer side of the class until the up/down jack pin snaps into the socket on the exterior mirror backing plate.

I accidently smashed the bowl insert of my 6 quart crockpot Where can I purchase a replacement one?

The only way is to replace the PDP panel if you want to fix it. It may cost you as much as to buy a new unit.