Question about Stanley Fatmax Xtreme Retractable Utility Knife

Open Question

Stanley knife 10-777 can not insert blade holder back into knife

Can not reinsert blade holder into knife body

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Just purchased a Stanley FatMax 10-778 retractable

1. Make sure the side lock is unlocked.
2. Push the thumb tab all the way to the front of the blade handle.
3. Insert the blade in the opening, you may notice two notches on the top side of the blade.
4. Press the small blade release button as you slide the blade into the knife. You may have to jiggle up and down to get the two notches on the blade fully into the handle.

If properly inserted, the exposed area of the blade should look very close to an equilateral triangle.

make sure both notches of the blade are inside the handle. They notch into the thumb lever.

good luck

Posted on Apr 11, 2010

Testimonial: "Thanks so much!"

Ad
nielsonplumb
  • 92 Answers

SOURCE: I have a stanley FatMax. How do I insert the blade

On the side there is a big gold wheel, twist counter clockwise and the case should split in half, the blade is held by a magnet, prise the old blade off and replace with new one, then put case back together and tighten gold wheel clockwise
Goodluck!

Posted on Mar 07, 2011

wentlanv
  • 710 Answers

SOURCE: When I inserted blade into

Hi Betsy,

Please go to this webpage and read the rants about this product.
Down towards the bottom are reviews written mostly by contractors and such. Review number 3 addresses your problems exactly. http://www.crunchgear.com/2008/12/05/review-stanley-fatmax-utility-knives/

Good luck

Handie Andie

Posted on May 10, 2011

cjdl52
  • 1 Answer

SOURCE: Stanley 10-777 utility knife: I need to reinsert

I had the same trouble. The blade holder was out of the knife and would not go back in. I fixed it this way: open the screw knob all the way to the least tension. Slide the two parts open but not all the way- there is a tab on the blade holder that gets in the way if you try to drop it in at the fully open position. With the two halves SLIGHTLY open- slide the blade holder in making sure that the tab is seated in it's slot. Depress the thumb tab and bring it to the most forward position and the two halves should be able to be seated together again.

Posted on Dec 12, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do remove the blades from the Rival 1220 model electric knife


I had the same question and finally figured out the answer. To remove the blades on the Rival Electric Knife 1220, first you must locate the piece I am going to refer to as the COLLAR. The collar is located above the "ON" button - toward the blades - but is not part of the blade. It is in between the main machine and the blades and kind of looks like a collar -it also looks like part of the main unit but when pushed from the top will move. On my 1220 it is the same color as the bottom of the machine. Once you locate this secret piece, the rest is quite simple. First-make sure the unit is unplugged then Just place your thumb on top and push the collar down-towards the sharp edge of the blades-and pull the blades out. To reinsert, line the blades up and snap them back into place.

Feb 16, 2013 | Rival Electric Carving Knife

1 Answer

Can't close stanley fatmax


It only goes in one way, try to loosen the screw a little

Jul 30, 2012 | Stanley Fatmax Xtreme Retractable Utility...

2 Answers

How to change blade on lenox gold utility knife. I've looked all over and cannot find instructions on product home page or anywhere online. HELLLLLLP! Thank you, Barbara


Open the knife to the middle position (don't open it fully) and push the small button on the blade holder. The blade will pull out easily..

Aug 05, 2011 | Garden

1 Answer

Can't reload utillity knife fat max10-778


Hi Mark,

I have several of them. Are you having trouble getting the handle to open up?

I have found that the blade needs to be all the way in to open it. Also, to get the blade holder to sit right.

If this is not the problem, please reply back. Thanks,
Handie Andie

Jun 21, 2011 | Stanley Hand Tools

3 Answers

Stanley 10-801 utility knife. How do you change the replaceble blade?


On the pivot end of the bladed knife is a black plug that says pull. They actually mean "Push". push it away from the knife body and rotate the handle half it's mounted in, down. The body will rotate in half , revealing the utility blade and more blades in the rear storage.Also note the blade depth adjustment has a locking detent. You have to push it to the right to unlock the utility blade.and push it to the right when retracting to fully retract and lock the utility blade.

Nov 26, 2010 | Stanley Garden

2 Answers

Stanley 10-777 utility knife: I need to reinsert the retractable blade slide back into the knife body. I try but the knife won't close.


I had the same trouble. The blade holder was out of the knife and would not go back in. I fixed it this way: open the screw knob all the way to the least tension. Slide the two parts open but not all the way- there is a tab on the blade holder that gets in the way if you try to drop it in at the fully open position. With the two halves SLIGHTLY open- slide the blade holder in making sure that the tab is seated in it's slot. Depress the thumb tab and bring it to the most forward position and the two halves should be able to be seated together again.

Oct 27, 2009 | Stanley Hand Tools

2 Answers

No running manual 4 summasign pro D610 vynal cutter


You can get assistance and possibly a manual for your Vinyl Cutter from a Summagraphics Repair facility such as
ADVANCED GRAPHICS
1027 N. MAIN STREET
TEL: 210-227-9393
SAN ANTONIO, TX 78212
I hope this helps. Toni Gallucci, Glass Act

Mar 17, 2009 | Computers & Internet

Not finding what you are looking for?
Stanley Fatmax Xtreme Retractable Utility Knife Logo

Related Topics:

1,756 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Measuring Tools & Sensors Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Frank Walton

Level 1 Expert

26 Answers

Are you a Stanley Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...