The led screen shows genera error

That is a service station shutdown failure.

Replace the Service Station, if that doesn't solve the problem, replace the PrintMech PCA.

mw tanya saya punya epson TX111 gimana cara mengatasi general error ketiga lampunya nyala bersama sama..mohon bantuannya...

The printer might General error or hardware error
Look into the head cleaning unit it might broken or not working properly. If the west ink is hard spry som water.

I found this on another website and it worked for me. It apparently resets the printer. Hope it works for you:

1.) power on (error message)
2.) press the "Stop (triangle)" and the "Colour copy" button and hold them
3.) press the power button to power off, still hold 2.)
4.) press the power button to power on, still holding 2.)
5.) the LEDs start to flash, then they stop to flash and the red exclamation mark starts to flash. Now release 2.)

6.) the LED should say: "Init EEprom"
7.) now press and hold the power button until the printer powers off and powers on again.

The waste ink tank is full.Read this instruction.
If this not help there is a manual reset for this printers but I'm not tried yet.

• Press and hold B/W+COLOR+STOP button.
• Press power button, don’t release all button until you see the led indicator blinking and a message display on the LCD.
• Release the button.
• Press COLOR button to clear protection counter
• Turn off the printer by pressing power button.
• DONE!

heres help CLICK Hope this helps please rate me

same here as well! waiting for a response

https://h30434.www3.hp.com/t5/Printers-Archive-Read-Only/on-the-display-of-the-printer-the-following-information/td-p/2243457?db=5


on the display of the printer the following information b817ed1c what to do


General steps to follow after hardware error above:

https://support.hp.com/us-en/document/c00489814

Hi,

I just like to ask to where specifically you can see the red light. It will help us determine what cause the red light. To give you heads up as well, the Printer's LCD screen can help us determine what exactly the offline condition of the CX3200 is:


Error message: No color or black ink cartridge-->Press the Color Copy button to install a new ink cartridge.
Solution: The indicated ink cartridge is not installed. Please install the necessary cartridge(s).

Error message: Color or black ink out -- >Press the Color Copy button to begin replacing the ink cartridge.
Solution: The indicated ink cartridge is out of ink. You will need to replace the necessary ink cartridge(s).


Error Message: Ink cartridge error -- > Press the Color Copy button to begin replacing the ink cartridge.
Solution: There is something wrong with the ink cartridge. Make sure the cartridge is genuine Epson ink. Also, try reseating the cartridge (remove it, and then reinstall it).

Error Message: Paper jam or misfeed -- > Press the Color Copy button and clear the paper jam by hand if necessary.
Solution: Paper is jammed. Check for any obstructions under the unit's cover, and in the paper tray.

Error Message: Paper out -- > Load paper in the sheet feeder and press the Color Copy button.
Solution: Load paper in the sheet feeder, and then press the Color Copy button to continue printing.

Error Message: Scanner unit open -- > close the scanner unit
Solution: Carefully close the scanner and press it down until it clicks securely into place.

Error Message: Scanner error -- > See your documentation and call service if necessary.
Solution: Press the ON button to turn off the Epson Stylus CX3200. Unlock the transportation lock, if necessary. If it is already unlocked, toggle the lock back and forth, 5-10 times. Turn on your Stylus CX3200 again.


Error Message: Printer error -- > See your documentation and call service if necessary.
Solution: Press the ON button to turn off the Epson Stylus CX3200. Disconnect it from power, and then reconnect it to power. Press the ON button to turn on the Stylus CX3200.

step1..............switch on
step2............press+hold stop,ink,power buttons untill printer switches self of
step3............switch back on and problems should have gone