I need charger to charge 6v battery

Hi Ebrahim
Defiantly not you cannot use a 12v supply on a 6v battery in the worse scenario you could blow up the battery by putting to much voltage into it, you will need to find a 6v charger hope this helps

you could try the original supplier or ebay and failing that you could try searching online for a pdf manual and just buy any charger that is the correct type voltage and most importantly polarity, having looked at the bike its a childs harley type bike and is 6v 4ah and likely a sealed lead acid type so i would buy a 6v 500ma lead acid charger, if there is a charge port you will need a plug to match and you will need to check the polarity is correct or if there is easy access to the battery terminals you could just use the crocodile clips to the corresponding terminals on the battery itself there is a selection of chargers here 6V Lead Acid Battery Charger eBay a 500ma charger will charge the bike in 8hrs the higher the ah the faster it will charge but i wouldnt go much higher than 500ma without checking with the vendor that it is suitable for a 4ah battery hope this helps

If under warranty have it repaired/replaced. If not under warranty then some basic troubleshooting. Most likely a battery issue howerver;


To test the fencer output you can power the fencer from either a standard 6V lantern battery (6V fencer) or a standard 12V automobile battery (12V fencer). You need to rig wiring observing polarity.


To test battery, remove and check voltage with digital volt meter.
A fully charged 6V SLA battery should read 6.2V minimum and a 12V should read 12.4V minimum. If a 6V battery measures 4 volts or less then battery has likely failed. Likewise if a 12V battery measures 10 volts or less it has likely failed. Before replacing a suspect failed battery, connect the battery to any standard 6V/12V automobile charger and see if it will take a charge. After the charging period;

• If battery takes a charge, reinstall back in fencer and see if fencer output is hot. If fencer fails output, repair/replace fencer. Else verify the fencer is charging the battery. While battery is installed in fencer measure battery voltage with a digital volt meter. Typical minimum voltage is 13.5V for 12V and 6.7V for 6V. If fencer fails to meet minimum battery charging voltage, likely the fencer solar charging system has failed, repair/replace.

• If battery fails to charge, likely battery is end of life. However fencer could still not work. Test fencer with alternate power source (see previous tests). If fencer ok, replace battery.

you need to recharge the mototr battery, it should be under the seat, the sounds on the steering wheel are run from a different battery source

1= test the selector, and clean it and repair or replace it if is mechanical or digital
2= tuner dirty, and clean it or replace.
3= see if the cable coming from the antenna or cable is loose or broken, or terminal damaged. and repair or replace.
see the diagram for tracking the signal
God bless you

can you send me a picture of what the battery connecter looks like, i probably have a charger i can send you

The couple of dryfit batteries I've looked at have been shot. I don't know how old they were. Take a decent modern battery charger (the ones at WallMart are good enough) that will handle 6 volt and AGM batteries. Clean the contacts and jury rig a way to connect the charger to the battery terminals. If the charger doesn't register anything, it's likely the batteries have died. They will actually completely dry out inside, becoming inert. I've used $20 AGM batteries from Batteries Plus and they seem to work fine (though you either need to make a battery adaptor, or cut out the side of the battery pack to get them to fit.

Product Detail Model No.: HB-1206S
The item is used for charging 6V-12V lead-acid batteries
Max Charging Current: 6A
AC Power Input: 64W
Output: 6/12V DC 3. 52A
Batteries Capacities: 15AHR-80AHR
Unit Packing: Colorful box
Dimension: 18cm x 10cm x 20cm
G. W. / N. W.: 1. 85KG/1. 75KG
Certifications: GS, CE, BS, ROHS, SAA

Main functions:
(1) The HB-1206S battery charger has the features of convenient operations, reliable safety and high performance.
(2) During charging, if turn up overload, the battery charger will keep itself at normal current and normal voltage with its self-automatic protecting function.
(3) If being short circuit, the battery charger will switch off itself, and turn normal after one or two minutes.
(4) The output current of the battery charger is very stationary, so it can protect the battery charger very well. It only costs 3 or 4 hours to fully charge the batteries.
(5) Indication of charging: the battery charger has 6 pilot lamps. The more pilot lamps shining, the less electric quantity is. The charging process finishes when all the pilot lamps go out.
(6) The battery charger can be switched between 6V and 12V, so it can charge for 6V and 12V accumulators. You can select 6V or 12V according to your own needs.
(7)The operations are very convenient: Put the red clip to the positive pole of the accumulator which indicated "+", and put the black clip to the negative pole of the accumulator which indicated "-", then plug in power source, the accumulator will be charged.

Here is the manual for your product. Please download, on page 6 it shows re-charging instructions for the battery. If this is not your product please let me know and I will find u the correct manual. Please go to:

http://service.mattel.com/instruction_sheets/N9733pr-0920.pdf

Please feel free to ask any follow up questions. If this was helpful to you, I hope you will leave me some positive feedback.