Return to factory settings

Reset to Factory Settings

• 1 Download the computer software for your Western Digital My Book World Edition if you don't have it installed on your computer. The software can be downloaded on the Western Digital website (see Resources.) Install the software to your computer.
  
• 2 Go to the "Start" menu. Click "All Programs," the "Western Digital" folder and then "My Book World Edition Software" to launch the software.
  
• 3 Switch to the "System" tab. Click either the "Restore Configuration" or "Full Restore" button on the tab, depending on your My Book World Edition drive.
  
• 4 Click the "Browse" button, select the factory settings default restoration point, and then "General Restore" to return the unit to factory settings, or click "Full Restore" and then "Restore Factory Default," again depending on your specific My Book World Edition device. The unit powers off, all data is erased from the hard drive and the My Book is returned to factory settings.
  

This is all I can find, might do the trick;
When changing the multiplexer to NTSC or PAL all other settings
are returned to the factory defaults.
The multiplexer can be used with either NTSC or PAL systems.
To set it up for NTSC operation:
1) Turn off the power
2) Press and hold the and {M} buttons.
3) Turn on the power
To set up the multiplexer for PAL operation:
1) Turn off the power
2) Press and hold the and buttons.
3) Turn on the power
Password Code User1 (1111)
User2 (2222)
User3 (3333)
User4 (4444)
Supervisor (5555)

capacitors in the switch mode power supply

If this is western digital world edition

Download the computer software for your Western Digital My Book World Edition if you don't have it installed on your computer.

The software can be downloaded on the Western Digital website.

http://support.wdc.com/product/download.asp?groupid=118&lang=en

Install the software to your computer.

Go to the "Start" menu.

Click "All Programs," the "Western Digital" folder and then "My Book World Edition Software" to launch the software.

Switch to the "System" tab. Click either the "Restore Configuration" or "Full Restore" button on the tab, depending on your My Book World Edition drive.

Click the "Browse" button, select the factory settings default restoration point, and then "General Restore" to return the unit to factory settings, or click "Full Restore" and then "Restore Factory Default," again depending on your specific My Book World Edition device.

The unit powers off, all data is erased from the hard drive and the My Book is returned to factory settings.

Hope this helps

There are two ways to do it. You can either update the firmware and it will erase everything for you, or you can do a factory reset, and return to factory settings. Go to Settings, PDN settings (not the Android settings menu) and scroll right to the Reset Defaults location. Tap on the reset button and you will be taken back to factory default settings. It might take a while to reload, but after everything it will be back to factory defaults from when you first bought it. Updating the firmware might be your best option if you care to resell it, because it may cause less issues for the next person and less chance of any returns.

Usually, this indicates that video source is PAL but the capture is set to NTSC, or that the video source is NTSC but the source is PAL.
Make sure that the video capture device is set to match the signal of the input.
PAL is used in Europe, NTSC in North America.
How you set it depends on the Video Capture software you use, but look for PAL/NTSC setting and switch it.

There should be reset button on the back of the router unit a pinhole if not then you may have to go into the router and reset to factory default that is log into the router with either 92.168.0.1 or 192.168.1.1 depends on the manufactuer.
You can also go to the manufacturers site and get the factory default or reset settings.

Reset All
This will reset the player to its original factory settings.
1. Press Menu to return to the Main Menu.
2. Move to Reset All and select it.
3. Select Save to reset to factory settings or Cancel to stop.

-Tha Mp3 Doctor

try unplugging everything take out your hardrive then plug the stuff back in

Phase Alternating Line (PAL) is a colour encoding system for analogue television used in broadcasttelevision systems in most countries broadcasting at 625-line / 50 field (25 frame) per second (576i)
NTSC is the video system or standard used in North America and most of South America. In NTSC, 30 frames are transmitted each second. Each frame is made up of 525 individual scan lines.
You might try disconnecting all power from the system. unplug it.
disconnect the TV. Power back up. Maybe it will reset to factory settings. See if your TV will have a switch to NTSC.