Question about Nikon D60 Digital Camera

1 Answer

Error. press shutter release button again

I CAN NOT CLICK PHOTOS. THE SHUTTER RELEASE BUTTON HAS STOPPED WORKING. THE MSG DISPLAYED ON LCD IS " ERROR. PRESS SHUTTER RELEASE BUTTON AGAIN". PLZ HELP

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Nikon Expert
  • 357 Answers

Most likely cause is failure of the motor in the SQ unit on the side of the mirror box. This ***** the shutter, raises the mirror, and operates the aperture unit. They're made in China, motors are **** This is a very very common problem, and the part is always on back order at Nikon. As Nikon has announced that they are going to stop selling parts - to anyone - in a couple of months you are probably better off sending it to them. Be prepared for a bill a little less than $200.

also if you pressed down really ******* the release to get it to fire, you may also have broken the release switch

Posted on May 09, 2012

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: nikon d40

Take the lens off and continue pressing the shutter untill it doesn't react anymore, you should then have a normal menu without the error message.Put your lens on and you're all sorted.Cheaper and less hassle than sending it to Nikon.
olly

Posted on Jun 01, 2008

dbarchitect
  • 150 Answers

SOURCE: Nikon d40x shutter stuck

The manual (pg 112) simply, and unfortunately, states this message "Press shutter release button again. If error persists, consult with Nikon-authorized service representative".

Some questions that might help: have you had the camera in some extreme conditions, damp, sand, etc. Clean the shutter button really well. Maybe use a small air blower and clean in the shutter release creases.

In the end, if the error continues, it will need to be serviced.

Posted on Jan 21, 2009

  • 1 Answer

SOURCE: faulty nikon d40

I had the same error message, the camera is less then a year old, however, I was taking up to 800 pictires every weekend of my kids soccer games, then a 6 month trip to the Pursian Gulf, that is when it started, I got back home, took it right in, and one year later after a few visits and calls trying to find out where my camera was, I finally got an answer back, they said I needed a new shutter which will cost $300, They said I should just by a new body for $400. What Nikon does is set that error message to pop up at about 35000 shutter releases, and you can't do a thing about it, once they hooked my camera up to thier system the said I had over 36000 shutter releases, where the average person takes 10000 a year and they want you to replace the body every 3 years....so before buying any camera, always check out how many shutter releases you can get when you buy a camera

Rob Smith
Victoria, BC

Posted on Sep 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to resolve error 5100 in canon mp 250 series printer pl tell me to do what


Error 5100 show your ink absorver almost full. So reset your printer by using the following methods. * Keep your printer off. * Now press stop/reset button and press power button with holding stop/reset button. * After your power is display a light release stop/reset button but still pressing power button. * Press Stop/reset button two times by holding power button. * Now release both button. * Wait for few minutes until your printer display "0" on your printer LCD. * Now download Canon MP258 reseter ServiceTool_V1050. After
pheireith244.jpg

Aug 11, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

1 Answer

"Error. Press shutter release button


hiit is not easy to tell what exact problem. It has quite of causes in your case. But I can only tell most common cause that it is sequence unit fail. It could also other like shutter fail, mirror box mech fail, motor fail, control pcb fail, and so on...etc...I recommended you bring to your local service place or Nikon service center which is helpful to you.

Jun 04, 2011 | Nikon D3100 Digital Camera

2 Answers

How can I stop displaying the photo information on the view finder?


In the viewfinder? The viewfinder will always display things like the f/stop and the shutter speed while you're preparing to take a picture. This cannot be turned off.

If you mean on the monitor on the back when reviewing your photos, simply press up/down on the multiselector to cycle through the different views of your photos.

Jan 10, 2011 | Nikon D40x Digital Camera

1 Answer

Nikon d90, blinking "Error"


You "release the shutter" by pressing the shutter release button, often called the shutter button. That's the button you press to take a picture :-)

The camera may or may not return to normal after that. If it doesn't, remove the battery, then put it back in and turn the camera on again. Try removing and reattaching the lens (with the power off). If the problem persists, have a certified Nikon tech look at it.

Feb 18, 2010 | Nikon D90 Body Only Digital Camera

1 Answer

Error Message


Try to take off the battery and reset the camera. You can also try to remove the lens and check the mirror opening..see if there is some thing stuck there. You can try to click the shutter while the lens is removed. If this procedure didn't work I suggest calling Nikon for further repairs.

Sep 25, 2009 | Nikon D60 Digital Camera with 18-55mm lens

1 Answer

Got the shutter and mirror clicks and err msg


bring it to your nearest nikon shop for a check up. i suggest a mirror lock up / shutter error.

Jul 26, 2009 | Nikon D90 Digital Camera with 18-105mm...

5 Answers

Faulty nikon d40


That may be the best advice :
http://nikon.com/

Jun 21, 2008 | Nikon D40 Digital Camera with G-II 18-55mm...

3 Answers

Error Code


No, it's not an error. What this display indicates, is the availability of the total number of photos you want to take. If the display says, "r06", then you are in JPEG Mode. If it says "r03", then you are either 1) in RAW Mode, or 2) have your Noise Reduction on (see FAQ #2). As you take a few photos in succession, you will notice the indicator drops by how many photos you took.

Mar 01, 2008 | Nikon D100 Digital Camera

Not finding what you are looking for?
Nikon D60 Digital Camera Logo

442 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nikon Cameras Experts

Ric Donato

Level 2 Expert

226 Answers

pictureman4u

Level 2 Expert

132 Answers

FIKRET UNALIR
FIKRET UNALIR

Level 1 Expert

239 Answers

Are you a Nikon Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...