My child pulled the string. The string will not go back in and will not make Woody talk. I cannot see a way to easily get into the white plastic cylinder. Part of which houses the batteries. It is inside Woody's shirt and will not easily come out. The string is sewn into Woody's shirt and vest.
A friend of ours gave our son a hand-me-down Woody doll with no string at all. I decided to see if I could fix it...about 4 hours, 1 soldering iron, and the realization that my eyes are failing faster than I thought, I was able to return Woody's voice. I'm sorry I didn't take any pictures, but here's what you'll need to do depending on what you find as you operate.
0. Perform of these steps over some sort of container to be sure that you don't lose any of the small pieces that may be liberated in this operation (particularly a small spring that comes later).
1. Take out the battery pack through his lumbar Velcro. There is a black wire that carries power into Woody's thoracic cavity to a module that houses the electronics.
2. You will have to untie, or otherwise get the string through the hole in Woody's back so you can work on it...I don't know what's at the pull end of the string since the Woody we inherited had no visible string.
3. Cut open the white fabric inside Woody that separates battery pack from the electronics module.
4. Take out the two screws that hold the two halves of the module together. CAREFULLY separate these as there are a couple of wires that run between the half with the electronics and the half with the speaker.
5. If you are lucky, which I was not, all the wires will be intact and you will only have to restring Woody. (Nervous sytem work (i.e. wiring) will require a soldering iron and perhaps the assistance of an additional set of hands...)
6. The string is wrapped around a spindle which is spring loaded on one side (it's the big spring - not the little one). With the spindle side of the module towards you (big spring to the lef), the string *should* come up in front of the spindle, over the top and down through the hole..at least think it should. Again the string was broken in ours and once I opened the module, I couldn't tell which way it was originally.
7. On the right side of the spindle is the mechanism that completes the circuit when the spring is pulled. This includes a small spring, and metal piece that makes intermittent contact when the spindle winds back up after pulled.
So, depending on what you see when you take the module and battery pack out you may find:
0. Oh, of course, replace the batteries just to be safe.
1. The string was just hung up in Woody's back and simply removing the module allowed it to be come free again. Piece of cake.
2. The string was bound up around the spindle in which case you just need to clear it and be sure that it winds up properly when pulled. You may need to rewind the string, in which case you need to lift the right side of the spindle (take care to observe how the spring and metal piece are configured...and DON'T LOSE THE SPRING..it took my 10 year old daughter's eagle eyes 5 minutes to find it after it went shooting off the table)
3. The spring mechanism is somehow stuck. This will require tweezers and some patience to sort out the cause.
4. You may have to replace the string. I found some laying around the house that was close to the small shred that remained in our Woody.
5. Finally, I actually had to solder down 3 wires to get the circuit to work. If you're in this predicament, let me know and I will draw a picture for you of what goes where.
In the end, I got Woody to talk again, though he tends to speak without being pulled from time to time. But I gotta tell you, the feeling I got when he burst out with, "Howdy partner, my name's Woody!" was about the best feeling I've had in a long time.
Good luck, and let me know if you need any more information.
Shawn
I have a loose wire, can you help? I had him all but fixed (pull string problem) but my husband "helped" and pulled a wire out!
Hi there, the problem with our woody doll is that the string was pulled to hard and seemed to either disconnected from the spring machism or the spring broke. I'm going to look at it again, but my question was...would know where I could find another spring? I've been thinking maybe from another pull string toy perhaps...but not too sure, thanks a lot
Please send wire diagram! One of the white ones connecting the voice box to the circuit board broke off, I know where one end goes but not other side.
×
19,006 views
Usually answered in minutes!
yes my son pulled the string a little hard I think.. and now it will not move either!.....
is there any way it can be fixed???
Hi
Please can I have schematic of circuit for pull-string Woody.
Well I would like you all to know this is July 2015 and the game is still on. The time spent has been in excess of 5 hours to relocate the drive spring - that took 3 hours - then replace the axle and cam. 2 hours later it was in place but when pulled no movement. Loosened it a bit - sound. Tightened it up - no sound. Mid-night gave up.
Will try again in 2020!
Thank you so much for this. I was into this issue and tired to tinker around to check https://tracktrace.one/usps/ if its possible but couldnt get it done. Now that i have seen the way you did it, thanks guys
with
regards
hello,
Thank you so much for sharing this helpful information, it helped me alot
Thanks and regards.:)
×