Bunn CWTF 15-APS Coffee Maker Logo

Related Topics:

Bob Brown Posted on Apr 02, 2012

Connect water line to bunn cwtf 35

What fittings or tubing do I need to connect the water supply to the coffee maker?

5 Related Answers

Kelley Hopper

  • 67 Answers
  • Posted on Feb 01, 2008

SOURCE: my bunn coffee maker CWTF-15 21604-0001

It sound like you are either missing the sprayhead or the temperature isn't hot enough. Check first to see if the sprayhead is there. It fits under the brew basket and looks like a little shower head - it's round and has usually five or six little holes in it. If it is missing your coffee will be weak due to the water not being spread across all of the grounds evenly.
The other thing to check is the temperature. Depending upon where you live the water should be between 185F - 200F. If the water is below that temperature the coffee may look like tea.

Ad

Steve

  • 3290 Answers
  • Posted on Dec 02, 2008

SOURCE: bunn omatic model F20 doesn't stop dripping

Check out:

http://whles.com/General%20Mtx%20Knowledge%20%20Tony%20Roach/BunnOMatic%20F35%20F20%20F15%20x.pdf

This is the free full service manual F15, F20 & F35 complete with troubleshooting section at the rear. This section has easy, plain english steps to follow to solve this very problem (others, too).

Good luck!

Anonymous

  • 1 Answer
  • Posted on Dec 11, 2008

SOURCE: my bunn coffee maker leaks

You need to replace the washer kit inside the top of the maker. Remove the 3 screws that fasten the top and lift it off. You will see the rocker leaver that allows the water to flow into the tank. At the point where the rocker stops the water there is a series of washers that degrade from the heat over time and allows the leak. The washers are very easy to replace. The problem is finding the washer kit. I found it at: www.buyitnow64.com for $3.95 plus shipping (FedEx is only $9.98). I bought 2 (one for backup) kits.The original washers lasted almost 6 years. I had repaired this problem before with a washer from my shop but it broke down rather quickly from the direct heat from the tank. This washer kit is a Bunn washer kit that is supposed to fit all Bunn machines both residential and commercial.
Hope this helps. It took me 2 hours on line to find the washers!

Anonymous

  • 131 Answers
  • Posted on Feb 10, 2009

SOURCE: Water supply for Bunn coffee maker

open the cover on the brewer- depending on your model, it could be the front or the back cover. look for a brew timer dial. turn this up slowly, running a brew each time to see if you now have a full pot

Anonymous

  • 189 Answers
  • Posted on May 19, 2010

SOURCE: Bunn coffee maker leaking from underneath the bottom

Please get the model and the date code from the bottom of the machine and contact customer serivce. Depending on the date code, there might be a seal kit available or the machine can be replaced at no cost if 3 years old or less. If it is over 3 years old and the seal kit isn't available, the machine will be replaced at a reduced price.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

Water is not hot when turn on

check the heat switch in the rear. if it's on, check the thermal fuse in the top right rear of the brewer. it'll be in a now browned tubing. you can get it through bunn (800) 352-BUNN (2866)
0helpful
1answer

Water not coming out of hot water spigot

thermal fuse is blown. it is located in the top, right rear of the machine in what is now browned tubing. you can either bypass the fuse with a jumper, or get a new part through bunn (800) 352-BUNN (2866)
0helpful
1answer

I need to ship a 3 burner BUNN CWTF 15-3. How do I drain the water out?

You can take the lid off and unscrew the nut that holds the water tray. Then take a 3/8 hose to siphon the water out of the machine.
0helpful
1answer

Bunn coffee maker heating element wont turn off

thermal fuse is blown. it is located in the top, right rear of the machine in what is now browned tubing. you can either bypass the fuse with a jumper, or get a new part through bunn (800) 352-BUNN (2866)
0helpful
1answer

Hi. how to connect water line from main to machine?

In the back of the machine is a copper (1/4" flare) fitting, From main water line you might have 3/8" comp or 1/4" comp fitting.
Find out the size of the fitting and if you have to get a flare to compression adapter for the fitting in the back of the brewer and the water line

Let me know if you need more help.

Note: If this going to be installed at a business you need to install a check/one way valve in the water line.
0helpful
1answer

Cwtf is a contant dripping from the dispenser funnel, how do i fix this?

Inlet valve is leaking.Valve is located by removing front access panel.Can be rebuilt using p.n. 1111.0002 repair kit.You can verify by removing top lid and finding water leaking at fill basin tube.
0helpful
1answer

Wiring

jumper the red and white wires at the terminal block
Not finding what you are looking for?

377 views

Ask a Question

Usually answered in minutes!

Top Bunn Coffee Makers & Espresso Machines Experts

vince

Level 3 Expert

2530 Answers

john h

Level 3 Expert

29494 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66925 Answers

Are you a Bunn Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...