How to connect usb cables inthe front panel to motherboard Gigabyte GA-6VM7A+

You can download "GA-G41MT-S2P" Manual and all the cable connections are in the Manual.

FYI
As for the Front Panel ATX casing cables connections, the "white" cables are the -ve polarity & the "coloured" cables are the +ve polarity.

Hope it helps.

Get the manual here:
http://www.gigabyte.com/support-downloads/download-center.aspx?kw=GA-G41M

Dodgy USB Controller chip. Send back for replacement/refund.

The Gigabyte GA-7VKMP motherboard does not support serial ATA SATA drives. Open the link provided; http://tw2005.giga-byte.com/Motherboard/Products/Products_GA-7VKMP.htm
2 x ATA 66/100/133 bus master IDE ports
1 x FDD, 2 x HDD and 1 x CD audio input
IrDA(1x5) and COM2 on board
GBT standard front panel
2 x USB2.0 connectors (support 4 ports by cable)

You can connect the adapter below to an opened IDE port and connect a SATA 1.5 drive to your system.
http://www.satagear.com/SATA-MM-A1_SATA_Adapter.html
This should allow you're SATA drive to transfer data faster than the 133MHz standard IDE speed.

Cheers'
Mike

Hi,
The USB pinout on all motherboards is as follows >>>>>>







As for the audio you can visit Gigabyte's support website for the schematics for the front audio.

Regards.

You will need the motherboards manual to help you with connecting USB_1, USB_2 and F_PANEL audio to you're case. If you do not have you're manual for the GA-8S650GXM you can download it from Gigabyte; http://america.giga-byte.com/FileList/Manual/motherboard_manual_8s650gxm_series_e.pdf
You will also need Adobe reader installed to view the manual.
Gigabyte GA-8S650GXM main web site; http://www.gigabyte.com.tw/Products/Motherboard/Products_Spec.aspx?ProductID=1658
Turn to page 18. Number 17, F_USB1/F_USB2. Use the link provided below to help you connect you're front case USB wires to the motherboard; http://www.directron.com/installusb.html
Turn to page 24, for front audio connections. Keep in mind once you configure you're audio to function from you're cases front audio port you will not be able to use the rear audio port. Caution, most people find bumping any front case USB or audio cords break far too easely. To avoid breaking the front audio port, consider using a Y splitter for the rear audio port as shown in the next link; http://shopping.yahoo.com/p:StarTech.com%20MUY1MFF%20Audio%20Video%20Cable:1991733360;_ylt=Ah94ikZN9zDbTi2.arc45BkbFt0A

Hope you find this helpful.
Mike

Here is the link for the manual. It will show the jumpers and pins for sending to the back and front. USB, sound, etc.

http://english.gigabyte.ru/products/mb/manual/ga-ma69vm-s2_10.html

Good Luck

black green white red inside row nearest battery,starting from the front facing end.

The problem is not with *********** Board. Check the front panel audio connectors inside your CPU are connected to *********** Board properly.

Aloke,
It does mention in your manual (top of pg. 28 -notes), that in order to use the HD Front Panel Audio connector the pin configuration are different than the AC97 connections. Your current case is set up for AC97. You will have to contact Mfg. for the case click the link for Gladiator support:
http://www.a-top.com/jsp/info.jsp?number=3

You can try this, open up your control panel, look for an icon that's named Sound Effects Manager. Open it. Click speaker configuration.
This is part of Realtec's software. This is where you can setup & check both front & back ports (Audio & Mic).
If this part of Realtec did not install goto Gigabyte & down load your audio software & re-install it. (Just a suggestion).
http://www.giga-byte.com/Support/Motherboard/Driver_Model.aspx?ProductID=2554

Hope this helps. If you make the call it will be a fix.
Good luck.