Color printing with green tint

Try to the clean the nozzles of your color cartridge. Refer to this article in the Lexmark website on How to Clean the Print Cartridge Nozzles with the Lexmark X7350. If problem continues, try to insert a different known working cartridge to deternine if your color cartridge is faulty.

hello

35 is color ink cartridge .. high yield,

A new color print cartridge needs to be installed.

If available, click the Continue button on your computer screen to print using the

black (or photo) print cartridge. (The Continue button is available only at the

beginning of a print job.)

Note: A variable amount of ink remains in the color print cartridge.

Follow these steps to replace the color print cartridge in your printer:

1 Cancel the print job if not already canceled.

2 Replace the color print cartridge with a new cartridge. For more information,

see "Removing a used print cartridge" on page 35 and "Installing print

cartridges" on page 35.

3 Print again.

To order supplies, click Order Ink on your computer screen. You can also see

"Ordering paper and other supplies" on page 40 in this guide.

Troubleshooting 54

manual = http://www.lexmark.com/publications/pdfs/2007/2500/v3708617_en.pdf

Installing print cartridges

1 If you are installing new print cartridges, remove the sticker and tape from the back and bottom of the cartridges.

1 2

Warning-Potential Damage: Do not touch the gold contact area on the back or the metal nozzles on the

bottom of the cartridges.

Maintaining the printer
35

list of ink cartridge part numbers
http://www.lexmark.ca/lexmark/product/home/455/0,6970,204812589_653399443_1037657543_en,00.html?tabId=7

Hmmmm.... Just a question, is it a brand new cartridge? If it is, it may be dried up.

start
control panel
printer and fax
right click your printer, choose properties
go tab by tab and look for print quality and then try
something like this
choose econo mode, or ink saving mode to start.

try to print in grayscale mode and use only the black ink cartridge.

that should be your new default, and you don~t have to change it from winthin other programs

Maybe you can try to rest the black ink level 1st. To reset the ink level:
1) Goto the Lexmark Solution Center application.
2) Press button Maintenance>Install a new print cartridge, follow the instruction on screen. U may then have your new full ink level. Note: u only can reset to full level, cannot customize the level by your own.
Hope this help.

YBC (/\)

Unfortunately the printer wont print unless there is ink in both cartridges

I had similar problem: everything muted and with brownish tint. Tried everything, finally discovered that I installed wrong cartridge: 6PC instead of 6C. The "photo" cartridges are pretty much the same, make sure you have the right ones: 6C, 6M, and 6Y.

hmmm...paperman..that's unusual to say the least..

Seriously, buy a new printer. Companies sell toner, not printers! The printer is basically a "freebie" and is a marketing vehicle to sell toner. I tossed my C510 into the dumpster. It had four new toner cartridges. System diagnostics said that everything was at 95% or better. The printer had about 1600 prints on it. The first set of toner cartridges (full at purchase!) printed great. Then, I got dotted lines on clean prints. Or, I would get washed out, yellow tinted print and often, there was no black print. I called a printer repair shop and they laughed and told me to chuck the printer - they were suprised it lasted through the first set of cartridges. Lexmark literally "ignored me to death."

I will NEVER buy another Lexmark. The Brother and HP color lazers are probably the best bet. I have two HP B&W's that are paper pumps - an old 4V and a 6MP. The sad part is that I paid a bit more for the Lexmark than the competing HP. You live and then you learn!

me too.