D-link dir-625 still cant acces wirelessly

You can setup a wireless network without a modem. It will allow you to share printers, files ect. The modem is required for an internet connection only. The modem basically translates the Ethernet traffic in to a signal that can be carried over your respective service, DSL over a POTS line or broadband over a coax cable. The word modem stands for MOdularDEModular note the word MODEM in there.

First of all make sure the Wireless switch in your Laptop is turned on.

Now Disconnect the cable from the Laptop to the Wireless router

Now go to your Wireless Network connection and search for the available network. Select the appropriate network and connect.

Thanks

Section 1 - Product OverviewHardware OverviewConnectionsUSB Connect a USB 1.1 or 2.0 flash drive to configure the wireless settings using WCN.Reset Pressing the Reset button restores the router to its original factory default settings.LAN Ports (1-4) Connect Ethernet devices such as computers, switches, and hubs.Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem.Power Receptor Receptor for the supplied power adapter.D-Link DIR-65 User Manual

If you don't know it you can check our list of default router and modem password list here.
If you have changed it and don't remember it you may have to reset your device to factory default using the reset button on most routers.

Use an Ethernet cable from the Ethernet port on your DSL modem to the 'WAN' port on the router.

Use another Ethernet cable from one of the 'LAN' ports on the router to the network-port on your desktop.

Click Start
Click Run
Type CMD
Press Enter
Type IPCONFIG
Press Enter
Look for output like: ... gateway ... 192.168.123.456
Start Internet Explorer
Type http://192.168.123.456 (or whatever value you saw)
Login to the router
Run its "Wireless Network Setup Wizard" to:
* set an SSID
* set an encryption-level, e.g., 'WPA' or 'WPA2'
* set a password
Use the SSID/password on your wireless laptop.

Have you connected the modem to the router using the proper wire?
This wire was provided by your ISP and is not a patch cable.
It must be plugged into the uplink port on your router from the modem box. This port is also called the wan or internet port on some routers.

it isn't syncing up with your modem, try a hard reboot, disconect everything, even the cable, after 5 minutes , first screw the coax cable back to the modem, that will re establish the cable connection, plug everything back in, and if that pc light still is still doesn't work, the router may be bad, look on the Dlink site and download the latest firmware, as a last resort, but also reset the router first before trying anything, there is a reset button on the router. Sometimes certain routers don't work with certain modems, if you try the reset, then the hard reboot, and the firmware, you have covered all the bases

call service provider (isp) to insure they have routers mac address. I cannot stress this enough

connect the the ethernet cable to the WAN port of the modem.

the connection should be:
One end of the cable is connected to the modem and the other should be connected at the WAN port of the modem.

Now use another Ethernet cable plug it in on the LAN port1 and the other end to your computer.

Access the configuration page of your router and set the wireless setting inside your DI-624 router.

If you have phone (DSL_ the phone must be connected to the modem of DSL, then connect the ethernet cable from the modem to the wireless router or router (use the jack WAN) and then from the modem (connect the cable into port # 1) goes to your PC into your ethernet card.

You have to access to your router and set your network (you have to put the data of your internet connection gave to you by your internet provider (usually is your email address and your pass)

You can get more help here:

http://www.microsoft.com/athome/moredone/wirelesssetup.mspx


If you have a wireless network Then do this:

Setting wireless network on Win XP
Click your Start Button
Select and click Control Panel
Select Network Connections
Select Wireless Network Connections
Right click
Select View Available Wireless Networks
5. Highlight the network you want to connect to
Click Advanced
6. Select the wireless network tab
7. Highlight the network in the available networks window
9. Click configure
9. IN the Properties Window
Double check the SSID (network name)
Enter the WEP KEY provided to you by the office
Click OK

unplug it and **** urself =] it will work than