At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
My new LG dishwasher manual said I can remove all 3 filter from the unit but they want come out ,the first one is removed by twisting but the but the upper sts filter wont come out and my dishwasher won't work HELP Please and Thankyou
Yes, what LG Dishwasher model for you have? Your question is classified in the LG LDF8812 question area.
But the LG 8812 does not have three filters. Just one that requires you to remove 10 phillips screws and the bottom sprayer arm. To remove the sprayer arm, just pull straight up and it will come off.Yes, what LG Dishwasher model for you have?
Your question is classified in the LG LDF8812 question area.
But the LG 8812 does not have three filters. Just one that requires you to remove 10 phillips screws and the bottom sprayer arm. To remove the sprayer arm, just pull straight up and it will come off.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
I had a similar issue, I am not sure if this will your issue or not, but it is worth a shot.
Mine threw the Vario motor error about 8 months into use and it was actually the impeller that pumps water around from the base of the unit. It was making contact with the filter/cover over it, causing it to spin too slowly and throw the error.
Both dish drawers had to be removed and about 8 screws in that secure the filter in the bottom of the unit. When you get the cover off check to see if anything is impeding the impeller, If not, Look at the bottom side of the cover. Mine had white streaks in a circular fashion. I scraped off the white plastic swirls with a chisel and verified the top of the impeller was smooth as well. Reassembled and it worked again.
Your dishwasher may have a filter located near the bottom or under the lower spray arm. This filter should be inspected and cleaned regularly. Follow your dishwasher owner's manual for specific instructions about how to properly remove and clean this filter, if equipped. If there are any holes or other damage to the filter, you'll need to replace it immediately to protect the dishwasher's pump and motor seals from damage.
Your dishwasher may have a filter located near the bottom or under the lower spray arm. This filter should be inspected and cleaned regularly. Follow your dishwasher owner's manual for specific instructions about how to properly remove and clean this filter, if equipped. If there are any holes or other damage to the filter, you'll need to replace it immediately to protect the dishwasher's pump and motor seals from damage.
Hi, F13 is an inlet fault. First the unit drains and then fills with water. When the unit has intially drained open the door and manually fill the unit with water, about 5lts. This will then allow the dishwasher to go to the next step which is to circulate the water. If this works ok then the water tap is defective, water inlet valve is defective or the electronic unit is not sending the signal to activate the valve. The water inlet valve is the white square box attached to the tap. Remove this and check the filter and make sure water comes out of the tap.If ok then remove the bottom panel of the unit under the door. On the right hand side there is a 2 core cable with a male and female connector. Unplug this and check for voltage from the electronic when the unit goes to fill with water. If there is 240v then the electronic is ok. You will then need a new waterproof system from Miele.
On the LG LDF6810 dishwasher, the best you can do is remove the bottom spray arm and then the 10 phillips screws that hold the filter down.
Pull the filter out and clean it as best you can.
Inspect the sump area beneath where the filter was. Be careful of broken glass and remove all debris. Use a flashlight and look into every little spot down there. Reassemble the dishwasher and operate your DW.
If you still have problems, I recommend a service call. Check your manual to confirm but most LG dishwashers have a 1 year parts & labor plus a 2 year parts only. Have your proof of purchase ready.
The LG dishwashers have a perminant mesh filter just below the bottom spray arm.
The filter can be removed by removing the spray arm by pulling straight up, then removing 10 phillips screws. Whenever you remove the filter, inspect for debris beneath the filter (including hard to see broken glass.)
hi The most common cause of an OE error code on a modern LG dishwasher is: 1. Blocked drain hose 2. Obstruction in the sump area (beneath the filter, which needs to be removed to check for onstruction) 3. Failing drain motor. else you need to REPLACE THE PCB POWER CONTROL BOARD
LG 2050 error 0E error. - You may not want to believe this but it is true!! My dishwasher has failed with 0E error 5 times now - it has cost me R350 each time - the problem IS NOT necessarily a blocked drain hose or the drain pump it could be the thermostat micro switch!!! the thermostat is located at the rear of the right bottom side of the dishwasher(held by oval nylon plastic housing). Turn the machine off. remove the right side panel.(remove top {2screws in lid at back}, remove right panel screws {2 behind door, 3 bottom back panel, 2 behind panel below door {pull panel out from top [no screws pushes in & out of place]}. Locate oval nylon/plastic shape located as above - micro-switch is in the middle (3 wire connectors in 1 block) thermostat is 2 connectors ( 1 each side of micro-switch). use screwdriver to push thermostat back into the nylon housing on both sides (it has worked its way out a bit over time and stops the micro-switch working). Reassemble and dishwasher starts to work again!!!! Good Luck - Alan
Hello, The most common cause of an OE error code on a modern LG dishwasher is: 1. Blocked drain hose 2. Obstruction in the sump area (beneath the filter, which needs to be removed to check for onstruction) 3. Failing drain motor. else you need to REPLACE THE PCB POWER CONTROL BOARD Good Luck!!!
Yes, what LG Dishwasher model for you have?
Your question is classified in the LG LDF8812 question area.
But the LG 8812 does not have three filters. Just one that requires you to remove 10 phillips screws and the bottom sprayer arm. To remove the sprayer arm, just pull straight up and it will come off.
×