Networking i bought a belkin wireless router to set up a wireless internet lan connection. i have connected all of the wires etc correctly and checked them with the instructions, the problem is, is that the host computer cannot connect to the internet via the eathernet port as the old adsl modem connected to the usb hub, also the host computer has a wireless network card and keeps picking up the signal from the router how can i stop this.

Connect a LAN cable from Belkin to your laptop/computer's LAN port, open a browser on your laptop/computer and enter the Belkin's configuration URL. http://192.168.2.1
The default PW = blank (just press Enter) You can now change the default admin password.
You can now configure the wireless settings to protect your wireless network and Internet from unauthorized access. Now configure the wireless card in your computer/laptop with the router's wireless settings. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Hi,

I got your issue, I hope you are trying to connect the 2nd router to the first router through LAN-LAN connection (i.e, LAN port of the first router is connected to the LAN port of the 2nd router)

Then you need to change the ipaddress of the 2nd Play Wireless router . Please follow these steps.

1. Connect the computer-router with ethernet cable and open up internet explorer and clear the address box and type in 192.168.2.1 and hit enter.

2. You will be logged into the Belkin router setup page, in the Left hand side under LAN setup click on LAN settings

3. It will ask for Login password, leave it blank and click on submit

4. Change the LAN ipaddress from 192.168.2.1 to 192.168.5.1 and click ok

5. The page will say cannot be displayed, then clear the address box and type in http://192.168.5.1 and hit enter

6. If your first router is connected to the internet , then automatically the internet status will says connected

7. You will be able to go online wired

Good Luck!
Thanks in Advance!

Regards,
Prema

ISP : EMBARQ

Step 1 : Connect Belkin - Computer ( Computer Should go to Any one of the four the Grey colored Wired slot)

Step 2 : Make sure the embarq modem is not connected to the belkin

Step 3 : Open the Router setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 4 : On The Left under LAN Setup Click Lan Settings

Step 5 : Leave the Password Blank And Click Submit

Step 6 : Change the LAN IP To 192.168.3.1

Step 7 : Click Apply Changes

Step 8 : Connect EmbarQ modem to the Yellow Slot in the Router

Step 9 : Connect Modem - Router - Computer ( Check if you Have Internet !)



Setting Up A Wireless Connection


Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.3.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works

Easy, if your modem is connected to your computer right now and internet is working all you need to do is connect your LAN line to your belkin router. the connection should say input, or Internet. after that you will need another LAN wire (These look like telephone cables but the jack plug is larger and will only fit a lan connection on your router or computer) Connect the second wire to the line 1 or outout 1 from your router, to your pc in the slot where the other cable was connected. your internet signal should work.... on your mobil find any available network and log in to your belkin router.

that should do it.... if you haven't set up your internet connection, do that first by installing the drivers for the modem provided by your provider and then complete the process above.

Wireless light will lit up only if any wireless computer is connected to Belkin's wireless network.
First, connect to Belkin's wireless network that you can scan.
After you connect, try to go online
It ll work...

If you connect the computer to the router , it works.
That means the wired connection is OK.
Open the set up page of the router check the wireless settings of the router.
I think your network is secured and you are not typing the correct network key.
just open the router set up and check the wireless settings .
Click Here for step by step solution

Starting from the obvious, check that the cables are installed correctly.
You have to have a cable that brings the internet to your place.
Connect that cable into the router's jack labeled Connection to Modem.
Then get another network cable and plug it into any other jack form the back of your wireless router, and the other end into your laptop, just to make sure you are getting connected.
Once you are sure you can surf the net, unplug the wire from your laptop, and you should be able to surf wirelessly.

And if you still can't connect, let me know to perform additional steps.

Please don;t forget to rate this answer if helps.

well, first of all the i also have the N1 belkin wireless modem router, in order for it to connect, there has to be a wireless connection in your area for you to connect to, if any of your neighbors so have wireless you can connect to their network, but if you are not getting a conection that means no one around you has wireless or lan, the belkin wireless is not a internet provider it just extends the distance of your internal wireless. some networks may be secured as well, sometimes you can only connect to unsecured networks unless you have the name and passcode for the secured network.

You may use your wireless router as an Access Point:

1. Connect one of the LAN port of the Belkin to a LAN port on your Voyager. If the link light on both side are not coming on, try using a cross-over cable. Important: Do not connect anything to the WAN port of your Belkin.

2. Configure the LAN IP address of your Belkin in the same subnet as the Voyager. By example, if your Voyager has 192.168.0.1, you may give your Belkin 192.168.0.3.

3. Disable the DHCP server on the Belkin since the Voyager most likely already has one.

4. Configure the Wireless parameter of your Belkin as you would normaly do.

Using this method, your wired and wireless devices will be able to communicate together since they will be on the same network and your Belkin will act as a bridge between the wired and wireless network.