Question about DeLonghi Nespresso EN660 Espresso Machine
Used to froth milk heaps better. Now seems to be letting more hot water thru and not frothing ther milk
I don't know why my answer posted in the comments section, so here it is in the proper area.
I had the same problem and was ready to send it in for repairs, but I talked to a great guy at Nespresso who helped me fix it myself. The problem was when I pushed the latte button, it would only froth milk for a second or two and then the espresso would start pouring. It basically refused to make a latte. Here's the things he had me do:
1) Descale immediately. I have an older machine, and descaling once a year does NOT cut it. He told me descaling every 5 months at the bare minimum, if your machine is not having any problems at all. Descaling is usually the main problem for lack of froth. I descaled and it seemed like the machine was working better almost immediately. I also ran 4 - 5 tanks of water through the hot water spout and the main espresso part (but mostly this is because it seems to take this much flushing to get the smell of the descaling solution out).
2) Reset your machine to factory settings. I have a classic Lattissima, so this is how you do it on that machine. Turn the machine on and wait until the drink buttons are steady (espresso and hot water buttons are no longer blinking to warm up). Then press and HOLD the power button until the espresso and hot water buttons BLINK THREE TIMES. Then they'll go back to steady again. You're now back to factory settings.
I did notice that I started having the trouble after moving the machine, so I'm not sure which of the above solved the problem. The main thing is it worked and I'm back to yummy lattes!
Posted on Mar 26, 2013
Not easy to post an answer!
I've copied from my comment post
Mine stopped pumping milk after 4 years of daily use. I tried all of the above (descaling and factory reset), but no luck. My husband figured out that residue buildup prevented a microswitch plunger from closing when the milk container was inserted. The plastic blades on the bottom of the milk container lid are supposed to depress the plunger so the pump will activate. Once he scraped the residue off, it worked fine.
Posted on Dec 08, 2014
After running a descaling cycle we then found that the machine was just not drawing milk at all from the milk receptacle. After trying all sorts of things over several weeks, I then decided to do a 'factory reset' by holding down all four coffee-option buttons for five seconds - and hey presto, it's now working fine! The machine seemed to get some sort of an bug in the electronics / programming.
Posted on Aug 19, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
per il milk island asciugare bene la valvolina e tutti i fori del blocco di plastica che fa da montalatte devono essere perfettamente asciutti dare dei colpetti alla valvola per fare uscire eventuale acqua all interno.
Posted on Apr 12, 2009
SOURCE: the milk frother has stopped
Good luck, same happened with ours. Solution? Buy a new one.
Posted on Jul 14, 2011
Testimonial: "i called them and replacing it seemed to be the only solution !!"
SOURCE: milk not frothing
called customer service. issue was, if you look at the hook where milk container connects, you should see two rings, green and black, if you don't this is what causing the issue. they send me new once w/o questions asked...
Posted on Jul 19, 2008
SOURCE: I have a Delonghi Magnifica
I purchased a unit second hand for my wife's birthday today. It's only 4 months old, got it home, tested it, same problem... No froth!
I've read all the posts here and all were very helpful troubleshooting guides however they did not solve the issue.
Understanding how the frothing mechanism functions is half the battle in figuring out the solution. It's a simple vacuum type system. No doubt you've read about checking the orings. This is definately the first thing to check however if this is not the reason then consider the following.
The larger of the white tubes that has the red and black oring inserts deep into its port on the tap. Why? It pushes steam past the milk pipe directly into the chrome frothing tube which causes a vacuum essentially drawing milk up it's hose creating the froth. What you can't see without further investigation is that on the underside of the tube centered between the red and black orings is a small hole. This hole is responsible for drawing the milk upwards. If this is blocked, and it probably is then no milk and no froth. Use a really small screwdriver to carefully clean the white tube both from the front and the little hole underneath.
So in conclusion. Any air leak between the red and black orings will prevent the vacuum required to draw milk up the tube and alternatively any blockage of the milk channel will also obviously prevent the flow into the frothing mechanism. Hope this helps.
Posted on Jan 10, 2010
they make one that has the option of frothing milk hot or cold. Blue light is cold. Red light is hot. The red light will always heat the milk. To get to the blue light, you need to hit the button twice.( First will go to red)
Posted on May 08, 2010
Tips for a great answer:
May 31, 2014 | DeLonghi ESAM6600 Espresso Machine
Feb 22, 2018 | Coffee Makers & Espresso Machines
Sep 28, 2017 | Gaggia Classic Espresso Machine
Aug 20, 2012 | DeLonghi Perfecta ESAM5500 Fully Automatic...
Jan 14, 2012 | Nespresso Aeroccino Automatic Milk Frother
Jun 07, 2011 | Gaggia Brera Coffee Maker
Sep 04, 2009 | DeLonghi Coffee Makers & Espresso Machines
Aug 08, 2009 | Nespresso Aeroccino Automatic Milk Frother
Apr 09, 2009 | DeLonghi Coffee Makers & Espresso Machines
25,113 people viewed this question
Usually answered in minutes!