Tv wont respond because device menu is changing through each device

Hello
Codes for RCA tv with Hughes remote are:

160 161 156 165 065 070 004 023 024
056 074 081 152 167 145
Code Entry

Use the REMOTE pane under the System Setup menu tab to program your

HRMC-11, HRMC-12, or HRMC-13 remote control to operate your TV, VCR,

SAT, AUX device, or DVD (HRMC-11 and HRMC-12 only). The AUX menu

button can be used to control a CATV box or other type of device. Use the menu

buttons to choose the desired type of device and display a brand name menu list
from which you can select the manufacturer of your device.

Code scanning

To use the Code Scanning method:

1. Repeatedly tap the top part of the CHANNEL (CH) button.

2. Continue to step through the codes until the component turns off, indicating

you have found the correct component code. If you accidentally pass a code

that responds or realize you may not have been aiming the remote control at

the component, tap the lower part of the CHANNEL (CH) button to step

backward through the codes.

3. Press the remote control POWER button to verify the proper code by

turning the device on and off.
4. Press the device button (in this example, TV) again to lock in the code.
OK

Check On the Menu Setup for On/Off Remote utility Maybe your Remote signal is off on the TV Set...

This sounds like the 'Other' connection jack has a bad internal switch. This switch in the connector tells the TV there is a device plugged into the external connections. A technician should be able to disable the 'Other' jack so it cannot be used. Try a service shop or even a technician friend for help.
**Caution. Hazardous voltages inside. Technical person only.

Here you go. This will work with most all universal remote controls. If you don't have the code do the following:
Automatic Programming
With automatic programming, the remote control tests all the codes available on the Code List and assigns the correct code for the selected device. Although this method can be more time-consuming, it eliminates the need to look up codes and enter them manually.

1. Turn off the device with which you want to use the remote control.

2. Press and hold the corresponding button on the remote control
(TV, VCR, SAT, DVD, CAB or AUD) until POWER INDICATOR illuminates. It should take a couple of seconds for the light to remain solid. The remote control is in programming mode.

3. Press and release power button. The POWER INDICATOR flashes once and stays on indicating the unit is in Power Scan mode.

4. Press CHANNEL up or CHANNEL down repeatedly until the device turns on.

5. When the device turns on, press OK to store the code.

Note:
• To exit without storing the code, press BACK.
• T he unit will search for the next code or the previous code if you press
CHANNEL up or CHANNEL down after the device turns on. (go slow you need to press OK when the TV turns on) if you mess up turn TV off and start over.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

Fill free to ask me questions about anything..........................

Here you go. This will work with most all universal remote controls. If you don't have the code do the following:
Automatic Programming
With automatic programming, the remote control tests all the codes available on the Code List and assigns the correct code for the selected device. Although this method can be more time-consuming, it eliminates the need to look up codes and enter them manually.

1. Turn off the device with which you want to use the remote control.

2. Press and hold the corresponding button on the remote control
(TV, VCR, SAT, DVD, CAB or AUD) until POWER INDICATOR illuminates. It should take a couple of seconds for the light to remain solid. The remote control is in programming mode.

3. Press and release power button. The POWER INDICATOR flashes once and stays on indicating the unit is in Power Scan mode.

4. Press CHANNEL up or CHANNEL down repeatedly until the device turns on.

5. When the device turns on, press OK to store the code.

Note:
• To exit without storing the code, press BACK.
• T he unit will search for the next code or the previous code if you press
CHANNEL up or CHANNEL down after the device turns on. (go slow you need to press OK when the TV turns on) if you mess up turn TV off and start over.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

Fill free to ask me questions about anything..........................

Hitachi: 1145, 0145, 0151, 1904, 0032, 0409,

or you can use the general method:
SEARCHING FOR YOUR CODE
If your device does not respond to the remote after
trying all codes listed for your brand, or if your
brand is not listed, try searching for your code. For
example, to search for a code for your TV:
1. Press TV once.
2. Press and hold P until the red LED blinks
twice, then release.
3. Enter 9 9 1. The LED blinks twice.
4. Aim the remote at the TV and press Power.
The remote sends IR codes from its library to
the selected device, starting with the most
popular code first.
5. If the TV responds, go to step 6. If the TV
does not respond, press CH+. The remote will
try the next code. Continue until the TV
responds.
NOTE: Press CH- to try the previous code.
6. To lock in the code, press P once. The LED
blinks twice.
7. To search for other device codes, repeat steps
1 to 6, substituting the appropriate device
key.

Programming a Device using Code Search:


1.
2.Manually turn ON your device (TV, VCR, Cable Box)
3.Press and "HOLD" CODE SEARCH
4.Press and release the device button you want to set up (TV, VCR, Cable Box) However, if you are using AUX for a device, press and release AUX first and then the device button for the type
of device to be programmed (TV, VCR, or Cable). The selected device button will flash once.
5.Release CODE SEARCH.
6.Press OFF/ON repeatedly until the device turns off (you may have to press up to 100 times at a rate of once per second).
7.Once the device turns off, press and release ENTER.
8.With the device on, press any other button. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-6.
Programming a device using the Code Lists:


1.
2.Find codes for each device and brand below.
3.Press and "HOLD" CODE SEARCH.
4.Press and release the TV, VCR or Cable button you want to set up. If programming AUX for a device, press and release AUX first and then the device to be programmed (TV, VCR or Cable).
When the selected device button flashes proceed to the next step.
5.Enter the three digit code from the TV, VCR or Cable Box code lists.

6.Release CODE SEARCH.
7.With the device on, press another button, for example CHANNEL UP. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-5 using
another code number from the lists.

Sorry it took so long to respond to your request for help.You have to use the function button for the television, to leave the dvd function to the television. Just push the button that say's TV and you will return to the television mode of the remote control. I hope this information helps you with the problem of switch the functions on you remote control to use the television.Thank you for using FixYa and have a nice day!

Resetting the TV
If the buttons on the remote AND the buttons on the TV case do not work (channels do not change and you cannot open or navigate the menu), the TV has stopped responding. Reset the TV as follows:

NOTE:
Some TVs have a reset button. If available and accessible, try using the reset buttons before using the steps below. Using the reset buttons can save time.


1. Unplug the TV power cord from the power outlet.
2. Unplug any connected devices (DVD, Set-top boxes, etc...)
3. Press and hold the TV power button for five seconds.
4. Plug the TV power cord back into the power outlet and turn on the TV.
5. Open the on-screen menu to confirm that the TV is responding again.
6. Turn off the TV and reconnect the devices.
7. Turn on the TV.

hope this may help;

Regards,
VOTIT

DON'T FORGET TO RATE:

Codes for Samsung (one of them should work on your RCA remote)

006,011,014,015,019,027,036,037,077

Programming Your Universal Remote.

The remote may already be set up to operate your brand of TV, VCR, or Cable Box. It is pre-programmed with following codes:

• TV-000
• VCR-000
• Cable Box-000
• AUX is programmed with VCR code 037

For brands that require programming, there are two ways to program: Using Code Lists or Code Search. Use Code Search if the code lists are not available or if the codes from the lists do not operate a device.

Programming a Device using Code Search:

1. Manually turn ON your device (TV, VCR, Cable Box)
2. Press and "HOLD" CODE SEARCH
3. Press and release the device button you want to set up (TV, VCR, Cable Box) However, if you are using AUX for a device, press and release AUX first and then the device button for the type of device to be programmed (TV, VCR, or Cable). The selected device button will flash once.
4. Release CODE SEARCH.
5. Press OFF/ON repeatedly until the device turns off (you may have to press up to 100 times at a rate of once per second).
6. Once the device turns off, press and release ENTER.
7. With the device on, press any other button. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-6.

Programming a device using the Code Lists:

1. Find codes for each device and brand below.
2. Press and "HOLD" CODE SEARCH.
3. Press and release the TV, VCR or Cable button you want to set up. If programming AUX for a device, press and release AUX first and then the device to be programmed (TV, VCR or Cable). When the selected device button flashes proceed to the next step.
4. Enter the three digit code from the TV, VCR or Cable Box code lists.
   
   
5. Release CODE SEARCH.
6. With the device on, press another button, for example CHANNEL UP. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-5 using another code number from the lists.