Question about California Creations Dp Rock Tumbler

1 Answer

The rock tumbler will not turn on, the light on the day settings just blinks off and on.

We did all the steps to tumble the rocks, when it came time to turn it on all it does is blink, the day setting button light just blinks off and on and will not start to turn the tumbler.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

The clear cover on top has a clasp at the BACK and a clasp with two clear pegs on either side of the clasp on the FRONT.. more than likely your two clear pegs are not closing the safety interlock, make sure you have the lid with pegs to the front and hold down while pushing the on button .. the lights blink to tell you the lid safety interlock is not secured.

Posted on Aug 19, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I received a national geographics tumbler for Christmas when I tried to use it the lid comes loose and spills water and stuff all over.


-Possibly too cheap and make form out side of USA.
Don't use it. Every time you use it. It'll do the same thing.
Or you can try couple more times to see what it'll do.


Good luck


Mai

Dec 27, 2017 | The Optics

2 Answers

Our Mitsubishi projection tv went out one day. When we went to turn it back on all it does is blink the green light for a few seconds and then shuts off. What could it be? Where can we look to see where...


MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:

UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ONFOR A MOMENT AND GOES OFF.

PRESS AND HOLD "device"(input) and "menu"buttons on front of tv for at least 5 seconds and then release both together.


Watch for power light to blink in a sequence:

1 blink-then 2 blinks-------no error

2 blink-then 1 blink-------X-ray protection

2 blink-then 2 blink-------SHORT PROTECTION*******

2 blink-then 3 blink---------deflection circuit problem

2 blink-then 4 blink---------vertical circuit problem


******2, then 2 is most common---usually means one of the fuses that protectthe Convergence IC or IC's is blown---set will detect no voltage to convergenceIC and shut down.


SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES ANDTHEN TO GET IT TO REPEAT MORE YOUHAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.


IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM

let me know what you find--hope that you find 2 blinks, a pause and twoblinks--this is the most common and easiest to fix.
SD TECH

Aug 09, 2011 | Mitsubishi WS-65807 65" Rear Projection...

1 Answer

How do you set the time as well as the timer? I have looked but can not find the manual.


Good Afternoon,

Programming Your Coffee Machine

• Plug in your appliance: the display will light up briefly in blue, blink "8888" and then remain

fixed.

• Press the O/I button if you wish to make coffee without using the programmable mode.

• The display will light up in blue and alternately show "ON" and the current time.

• Press the O/I button to shut off the coffee machine. The display will no longer be lit.

Setting and Adjusting the Clock

• The machine must be "off".

• Press and hold the prog button (o) for 3 seconds: the hours will blink "88 _ _".

• Adjust the hours in steps by pressing the h/min button (n).

• Press the prog button : the minutes will blink" XX 88".

• Adjust the minutes in steps by pressing the h/min button.

• Confirm the setting by pressing the prog button.

Setting Auto On

This programs the coffee machine to start automatically at the set time each day.

• Press the prog button (o) briefly : the display will blink "prog" for about 1 second, followed

by "8888".

• Press the prog button briefly: the hours will blink "88 _ _".

• Adjust the hours in steps by pressing the h/min button (n).

• Press the prog button briefly: the minutes will blink "XX 88".

• Adjust the minutes in steps by pressing the h/min button .

• Confirm the setting by pressing the prog button briefly:

• The display (q) will show the time and a " ".
• Press the h/min button to cancel the programming.

Click the link below for the maunal:

http://www.krupsusa.com/NR/rdonlyres/A50B1840-2CD9-44C1-87E8-260B92D96D3A/7244/FME124_FMF345_usa.pdf

Hope this helps!

zeppelinx12

Feb 23, 2011 | Krups FME2 Coffee Maker

1 Answer

Everytime you put your card in, you have to move the dial on the side to say in our out on your shift?


this should fix your problem
HOW TO USE YOUR TC100 TIME CLOCK Step 1: Remove the front cover - see enclosed instruction sheet on page 5. Step 2: Program the Date & Time and Print Method using the 3 buttons: Mode, Select, Setting: Date & Time: Press the Mode button. The Hour will start blinking. Press the Setting button until the correct hour is displayed. Press Select to set the hour shown. The Minutes will blink. Press Setting until the correct minutes are displayed. Press Select to set the minutes shown. The Seconds will blink. To set the seconds at 00, press the Setting button. Press Select. The Year will blink. Press the Setting button until the desired year is shown. Press Select to set the year shown. The Month will blink. Press Setting until the correct month is shown. Press Select to set the month shown. The Day blinks. Press Setting until the correct day is shown. Press Select to set the day shown. Print Method: Press the Mode button until P5 (Program Mode 5 for Print Format) is displayed. Press Setting to choose one of the following Print Methods. The TC100 has two settings for print activation: Manual or Automatic 1 = Automatic (default setting) - The TC100 automatically prints when the time card is inserted. 2 = Manual - After inserting the time card, press the Print Button to activate printing. Press Select to confirm the Print Method chosen. Press Mode

Jan 27, 2011 | The Times ROYAL TC100 TimeMaster Time...

1 Answer

We have a rock tumbler and have lost the instructions. How long are we to tumble each stage? I assume that the sand goes inside the tumbler with the rocks. We need some directions.


Fill the barrel most of the way with stones, add coarse grit, add enough water to just cover the stones and then clean where the lid seals carefully. Seal it up and run it for a week, dump everything into a colander and rinse. Don't run that mud down your drain because it will plug it mightily, run it outside.

Do the same process with the fine grit, run it for another week and rinse and admire.

lp

Jan 02, 2011 | Edu-Science Toys

1 Answer

Where can i find a set of instructions for our edu science rock tumbler.


I used to have exactly that same rock tumbler. I have a bunch of polished rocks out in my garden that the kids and I made with that thing.

I don't have the instructions, but there are some perfectly great generic instructions on the geology.com web site: http://geology.com/rock-tumbler/rock-tumbler-instructions.shtml

I used these directions with great success.

Dec 31, 2010 | Edu-Science Toys

1 Answer

My daughter received an Edu Science Rock Tumbler for Christmas but has lost the instructions. Where can we request for a new set of instructions?


Wow that is a nice one you have, it is probably quieter with the plastic cover. I use to tumble my rocks either in the basement or in an empty drawer in my dresser to sort of block out some of the noise. The one I had when I was younger was probably the first do it yourself old Smithsonian rock tumbler. I'd say that was probably one of the best gifts that I have ever received.
Well, first, you put the bag of rocks that you want to tumble in the tumbler. Make sure it only fills the barrel 2/3-3/4 full or you may have to extend polishing time.
then, usually you use the thickest to the thinnest grit in that order. You put the thickest grit in first and let the rocks tumble from 7-10 days (for optimal polishing). You will do this for each grit you use.

Make sure there is no grit transferred from one step to the next. Hope this helps :)

Dec 28, 2010 | Edu-Science Toys

2 Answers

We lost the creatology rock tumbler instruction manual and cant do anything with out it


Hi, We got the same tumbler this Christmas. You might be able to get an manual from service@bhsciencetech.com
To get started though, Step 1 takes 2-4 days, step 2 4-7 days, step 3 2hrs, step 4 2 hrs.
To start day 1
1) rinse stones with water and fill barrel with no more than 8 oz of stones
2) Add step 1 course Grinding Powder
3) Add enough water to cover stones
4) tighten (snugly) cap on barrel to prevent leaking
5) Be sure barrel is clean & dry. Fit barrel into tumbler (fits correctly only in 1 direction). Cover barrel with safety dome.
6) Attach DC plug to tumbler and plug in.
7) Push on/off button
8) Push # of days button timer.

Extras
They suggest using a lubricant on the inside rim of lid to help removal.
Once you start the tumbling do not turn it off and leave it off - It will harden like cement inside the barrel.
It is loud so place it on a towel to help reduce noise and put it where it won't bother anyone.
Good Luck and Have Fun

Dec 26, 2010 | Toys

1 Answer

Hi. Can you please tell me the correct code for the Curtis tv for Cablevision Remote? We have two remotes now, the cable remote cannot operate the volume or the power on/off tv, must use Curtis remote.....


Hello
Codes for Curtis TV with Cablevison remote control are:-

070 004 101 127 236 011 072 081 120 164

*Tip: The iO button will light on for 20 seconds. The

next step must be entered while the iO button is
on.

STEP2 Press the [INFO] button.

The iO button will blink number of times indicating the

number of each digit of the code number. Each digit is

separated by a 1 second interval of the iO button being

turned off.

Example :One blink, three blinks and eight blinks with

an interval of 1 second of iO button being

turned off, indicates the code number 138.


Note :Ten blinks is equal to the number 0.


D. Program the Volume Controls.

By following the steps below, the user can program

the volume controls (Volume UP, Volume Down and

MUTE) . The default volume control settings on the

remote control is TV volume control. If you wish you

can control the volume via your CABLE box, use the

following steps.

STEP1 Press the [CBL] button and the [SEL] button

simultaneously for 3 seconds. The iO button

will turn on.

*Tip : The iO button will light on for 20 seconds.

The next step must be entered while the

iO button is on.

STEP2 Press the [VOL +] button.

STEP3 Press the [CBL] button.

The iO button will blink twice to confirm the

programming.

To return to original state:

If you wish you can control the volume via your TV,
repeat the above steps by pressing [TV] in STEP3 .
OK.

Dec 23, 2010 | Curtis CM13102 13" TV

Not finding what you are looking for?
California Creations Dp Rock Tumbler Logo

Related Topics:

404 people viewed this question

Ask a Question

Usually answered in minutes!

Top California Creations Toys Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

28784 Answers

ray gallant
ray gallant

Level 3 Expert

63881 Answers

Are you a California Creations Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...