Question about Nordic Track C2255 Console (treadmill)

1 Answer

Treadmill won't start. Console works but when push start or any of the buttons it beeps and nothing happens. It incline, change speed. I unplugged and restarted but nothing.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nordic Track Master
  • 12,223 Answers

If the console takes batteries, replace them. If this does not work or your console does not require batteries, check the reed switch or optic sensor. Reed Switch: Unplug the treadmill and remove the motor hood cover. The reed switch is mounted on the frame next to the front roller pulley. There is a magnet glued into the front roller pulley. When adjusting the reed switch, make sure it is pointing directly at the magnet. Move the tip of the reed switch within 1/8" of the magnet. Also, check to see that the wire is not damaged, and is connected to the console
.
Optic Sensor: Unplug the treadmill and remove the motor hood cover. The optic disk and sensor are located either at the end of the motor or the right hand side of the front roller. The optic disk spins between two sensors on the optic switch. The disk must spin freely without touching either sensor. The sensors can be moved by loosening the adjustment bolt holding the switch to its bracket. The switch can then be slid. Center the disk.
Treadmill won't start.  Console works but when - 11_21_2011_11_34_59_pm.gif11_21_2011_11_35_24_pm.gifRemember the Display Console Board has circuit that send to PController Motor, and after you did the adjustment you can conclude if the Sensor Reeed is faulty, 2) The Display of 3) The main Controller Motor.

Posted on Nov 21, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Horizon treadmill won't incline


Step 1:

see the diagram attached.

Clean the motor, lube the gear+shaft
Adjust the small POT for a little.
RUN the software calibration for troubleshooting. see the diagram
2_8_2013_11_10_42_am.gif

Step 2:

2_8_2013_11_11_14_am.jpg

Step 3:

2_8_2013_11_11_47_am.jpg

Step 4:


he Steps for Newer Style Console Calibration
1.Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
2.Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
3.Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
4.If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
5.Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
6.Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
7.Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
8.Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
9.Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
10.Press ENTER. You should see "SS" or "55" in the console.
11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
12.Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
13.When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
14.Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
15.If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.
God bless you

Feb 07, 2013 | Horizon Fitness Horizon T101 9 Program...

1 Answer

PaceMaster Bronze Basic err 119


Run the software calibration for easy diagnose, and troubleshooting see the steps. and Block diagram
God bless you

The Steps for Newer Style Console Calibration

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Jan 14, 2013 | PaceMaster Bronze Basic Treadmill

1 Answer

Bowflex tc20 won't go above speed 1


RUN the software calibration for easy diagnotic, troubleshooting, and fix it. God bless you
Proceed with this steps.

The Steps for Newer Style Console Calibration:

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.



Jan 08, 2013 | Bowflex Treadclimber

1 Answer

Treadmill belt runs too fast and will not power off with control panel


Step 1:

test the speed sensor,m for open or faulty, clean it, and tight the connector. see the diagram attached.
However follow the steps for RUN the.s calibration for fix it.
God bless you
1_7_2013_11_03_18_pm.gif

Step 2:

The Steps for Newer Style Console Calibration:
  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
  10. Press ENTER. You should see "SS" or "55" in the console.
  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Jan 07, 2013 | Exercise & Fitness

1 Answer

Nordictrack COmmercial 1500 console buttons don't work


http://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnes

11_17_2011_8_43_24_pm.gifsincerely. Please keep me in touch.

Nov 17, 2011 | Nordic Track NordicTrack Commercial 1500...

1 Answer

How do you recalibrate A2050 incline


The Steps for Newer Style Console Calibration:
  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
  10. Press ENTER. You should see "SS" or "55" in the console.
  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Sep 06, 2011 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

My console does not allow me to change the incline, speed, etc. The control panel does not acknowledge the buttons pushed. I've turned it off and on.


my treadmill is doing the same thing. the only buttons that work are the start; incline up. 4 incline; 8 incline; and 11 incline.

Sep 26, 2009 | Reebok 8700 ES Treadmill - Silver Service...

1 Answer

Beeping NordicTrack Ifit treadmill


please try to tight the connector to the side of Console, Clean it with special contact cleaner contact.
2) Open the cover where main motor is there tight the connector coming from the controller motor board, and clean too, with special contact cleaner.

3) If the problem persist you must replace the Complete console CPU.
bLESSING.
cuadra2016@yandex.com
whatsapp:+50588611441

Nov 01, 2017 | Nordic Track NordicTrack Treadmill, A2550

Not finding what you are looking for?
Nordic Track C2255 Console (treadmill) Logo

602 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Treadmill Repairs...
Treadmill Repairs...

Level 2 Expert

338 Answers

Android Man
Android Man

Level 2 Expert

278 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...