JVC problems Mike, I seem to be having the exact problem described - your response is below - my question is roughly how much would a repair like this cost. My tv is 2 ys old and cost about $400 when new, is it worth spending the money to fix it or should I get a new one? I'm not sure of the model number, its a 32" JVC iArt CRT Thanks, Jay It is not a fuse, since if the fuse was bad, the power LED would not light at all. I have seen that symptom many times and I usually find 2 problems which cause this. On some sets, one of the larger caps in the power supply's secondary side degrades just enough that the set will not start. On other sets, I usually find that the small transistor that turns the relay on has shorted out, and the 11 volt zener diode next to it is usually shorted too. The transistor is a very small surface mount transistor, so the set should be serviced by a qualified tech experienced in JVC sets.

Start by testing alternator and battery most auto parts store will test for free.

This is most likely a defective zoom rocker switch assembly and can usually be repaired fairly inexpensively. However, it's not a user serviceable problem and will need to be repaired by a qualified service technician.

My name is Rick and I'm a professional repair technician with over 20 years in the business and have repaired many of these. I'm semi retired and work from home with little overhead so I can keep repair costs low. If you decide to have the camera repaired, please click HERE for a directory listing that suits your needs.

If this response has been of any help to you, please be sure and give a positive vote for me on FixYa.com.

There seems to be issues with the soldering on it getting old and loose, also there are some common parts that burn out or go bad over time. I am not sure if you want to spend the money or are going to be able to find someone to fix it.

This is usually caused by a defective CCD image sensor and can be repaired fairly inexpensively. However, it's not a user serviceable problem and will need to be repaired qualified service technician.

My name is Rick and I'm a professional repair technician with over 20 years in the business and have repaired many of these. I'm semi retired and work from home with little overhead so I can keep repair costs low. If you decide to have the camera repaired, please click HERE for a directory listing that suits your needs.

If this response has been of any help to you, please be sure and give a positive vote for me on FixYa.com .

if you tap the EGR valve and you get a response replace it
if you tap anything else and get a response replace it

This is usually caused by a defective CCD image sensor and can be repaired fairly inexpensively. However, it’s not a user serviceable problem and will need to be repaired qualified service technician.

My name is Rick and I’m a professional repair technician with over 20 years in the business and have repaired many of these. I’m semi retired and work from home with little overhead so I can keep repair costs low. If you decide to have the camera repaired, please click HERE for a directory listing that suits your needs.

If this response has been of any help to you, please be sure and give a positive vote for me on FixYa.com .

Had exact same problem after driving 120 miles in Florida heat. After 30 minutes started but ran rough for a day and now seem fine. Thought at first fuel filter or dirty gas. Going to replace filter anyway. Is this a common problem?

$$$$$ from you

The link below describes disassembly of the dryer you have . You will notice that the manual is for Westinghouse and Frigidaire. GE must have had some made for them also. Circuit diagrams and control panel appearance may not be exactly the same but disassembly will be.

The disassembly section begins at page 61.

DBL333EB3WW Service

The problem you describe is common to JVC amps. This control has a motor mounted on the back of the circuit card that drives the volume control up or down using the remote control for this system. The looseness of the volume control cannot be repaired. The shaft has separated from the potentiometer. I don't know if JVC has this part any longer but it has to be replaced as a unit (volume control card).