Remote disconnection. when connecting the wii fit balance board i pressed the red sync buttons for longer than 10 seconds and now the wii remotes are disconnected. the screen states wii remotes disonnected press A but i cant get any wii remotes to work, have tried different batteries etc..... in the instruction book it says IMPORTANT! do not press sync for more than ten seconds or you will disonnect the remotes. please help.....

You need to sync the balance board with the Wii. It's easy to do and takes 10 seconds.

1) Start Wii Fit.
2) When it asks you to push the power button as you're describing, open the SD card slot on the front of the Wii and observe the red button.


3) Now, flip over the balance board. Remove the battery cover on the bottom of it, and press the red button beside the batteries, and the blue light should start to blink.


4) While the blue light on the balance board is still blinking, quickly press the red button on the Wii. If they are both blinking at the same time, they should be syncing to each other.

5) Your Wii Fit Balance Board should now be synced with your Wii! If it has been synced successfully, you will no longer need to sync it, and should now automatically connect when the button is pressed with your foot.

Just re sync the remote. I had to do it earlier again when I was trying to fix my Wii Fit Balance Board. :)

If you hold the SYNC button in the SD Card Slot on the Wii console for too long (10 seconds or longer), all the remotes synced to your Wii will be erased and then you have to sync them and the Balance Board again.

Visit support.nintendo.com

Or call 1-800-255-3700 for assistance on your Wii

there are series of problem in wii which can be solved without much technical knowledge ........ your problem belong to that so dont worry i will give you the link to download the wii repair guide that will help you a lot Click Here

Looked around for a solution for a long time for this one.

1) removing the batteries from the Wii Fit balance board for at least a minute.

2) Turn the Wii OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds plug the cord back into the outlet.

2 Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This should clear all the old syncs on the Wii.

3 After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:

a With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

b Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will turn on.

c Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console.

d When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

4 Start the game from the Wii Menu, don't forget to sync the Wii Balance Board from the opening screen of the game (you've deleted the syncs earlier).

Another problem may be the surface on which you post the Wii fit, make sure it's flat, try put it on the floor directly or place it on a rug.

And don't forget to "step on" it when it says and not before as the Wii console might be "overloaded".

Hello,

Here you have different procedures on what to do if you get that error message. Please get back to me if nothing works.

The exact procedure is:

• Even if the battery level is strong, try the following:

Remove the batteries in the Wii Fit Board for at least 1 minute…… better 15

Try these steps!

1 Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.

2 Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

3 After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:

a With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

b Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

c Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).

d When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

4 Start the game from the Wii Menu, then sync the Wii Balance Board from the opening screen of the game.

Hope it helped.

Unplug the AC adapter on your console out of the Power cord then wait 15 min and plug it back again.Open the front cover on your Wii, then push the red button there, then open the batteries cover on your Wii Fit and push the red button there.If this not help press and hold the red button on your Wii for 20 seconds.This will clear all synced Wii Remotes from the console.Then repeat the procedure again.In this case you need to SYNC your Wii Remote too.If this not help your Wii Fit may need service.

Unplug the AC adapter from power cord then wait 10 min and plug it again.Open the SD Card slot cover on the front of the Wii console, just below the disc drive, and press and hold the red SYNC button for 15 seconds. This will clear all synced Wii Remotes from the console.Then push the red button again, then open the batteries cover on your
Wii Remote and push the red button there.After that push the red button on console one more time, then open the batteries cover on your Wii Fit and push red button there.If this not help may your wii fit need service.

You need to sync the balance board with the console. Instructions are in the manual. Sync button for board is in battery compartment and sync button for console is in panel under reset button.

Took a few tries for me, be carefule not to hold sync button on console down for longer than 10 seconds because it will deregister all wii remotes.

are you able to get any of your controllers to connect? if not it could be a issue with your sensor bar. please provide a bit more info

but try this first

Synchronizing the Wii Balance Board with your Wii Console
IMPORTANT: To operate correctly, the Wii Balance Board must be synchronized with the Wii console using Standard Mode Synchronization. Follow the steps below to synchronize the board to the console.

• This procedure must be followed for each Wii Balance Board compatible Game Disc.
• These synchronization settings will be saved even if the console is turned off.
• This procedure can be completed only if a compatible Game Disc is running in the console.

1. Press the EJECT Button on the front of the Wii console and remove any
   game disc if necessary. Insert a Wii Balance Board compatible Game Disc.
2. Use the Wii Remote to select the Disc Channel on the Wii Menu screen and select START.
3. Open the SD Card slot cover on the front of the Wii console.
   NOTE: Close the SD Card slot cover when you are finished with the synchronization procedure.
4. Remove the Battery Cover on the bottom of the Wii Balance Board.
   NOTE: Replace the Battery Cover when you are finished with the aynchronization procedure.
5. Press the SYNCHRO Button (SYNC.) on the Wii Balance Board. The Power LED on the board will start blinking (for up to about 20 seconds).

Press the SYNCHRO Button (SYNC.) on the console while the Power LED on the board is blinking.

1. IMPORTANT: Do not press and hold the SYNCHRO Button on the Wii console down for more than 10 seconds. This will delete all of the Standard Mode synchronization information for all Wii Remotes that you use with that console.
2. The Power LED will stop blinking and light steadily once the synchronization is
   complete. You are now ready to play the Wii Balance Board compatible Game Disc. Please refer to the instruction booklet for the Game Disc you are using for further information on gameplay.

• Only one Wii Balance Board can be synchronized to a Wii console at a time. Up to a total of 10 Wii Remotes and accessories can be synchronized to a console at any time with the Standard Mode procedure. If additional synchronizations are made, the oldest existing ones will be overwritten.
• The Wii Balance Board can only be synchronized to one console at a time using the Standard Mode procedure. If you change the console you are using the board with, you will have to repeat the synchronization procedure each time.
• The Wii Balance Board uses the Player 4 (P4) connection. If a Wii Remote is actively using P4, that remote will be disconnected while the board is being used.