Outside temperature doesn't display on atomic clock. Skyscan #86722

Howdy. Skyscan cannot locate your model number, but think the guide for a slightly different model should work. Here is the link to the instruction manual at skyscan's website: http://skyscaninfo.com/content/manuals/25-model-86722.html
I hope this gets you going:)

Hello. The instructions to set these clocks are rather lengthy so here is the website. Find your model, or one like it and the directions are very straight forward. Regards, Joe
http://skyscan.info/content/manuals/25-model-86722.html

Seems to be a consistent problem with Skyscan. I have the 88800 model and my outdoor transmitter isn't transmitting the temperature either. We've replaced the batteries in both the transmitter and clock and nothing for outdoor temp. It's only been used for 9 months.

Online manual is at link http://skyscan.info/content/manuals/25-model-87315.html

Please check the following website for all the info and faq.

http://skyscan.info/content/index.php?option=com_content&task=view&id=35&Itemid=40

Also,

If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappers.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.
6. Bingo. You are in business.

Try changing the batteries in the CLOCK. I had the same problem in a 3M similar clock and it didn't read the transmitter correctly or eventually, at all, when the CLOCK batteries were getting low.

Please check the following website for all the info and faq.

http://skyscan.info/content/index.php?option=com_content&task=view&id=35&Itemid=40

Also,

If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappers.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.
6. Bingo. You are in business.

Please check the following website for all the info and faq.

http://skyscan.info/content/index.php?option=com_content&task=view&id=35&Itemid=40

Also,

If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappers.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.
6. Bingo. You are in business.

Please check the following website for all the info and faq.

http://skyscan.info/content/index.php?option=com_content&task=view&id=35&Itemid=40

Also,

If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappers.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.
6. Bingo. You are in business.

FixerUpper

You need new SioScan Temperature Transmitter 433 MHz. Take a look on amazon La Crosse Technology TX6U Wireless Temperature Sensor for 433 MHz units.... Hope this was helpful. cheers