Unlock Region Code

http://www.multi-region.net/lg
shuold do it

here is one way:
To change the player region code
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, * requested region code here (1-8) *, Subtitle, 1

3. Player will reset and requested region code will be set.
- For example to set region code to 3 press: "Enter, 6, >=10, <<, 00F2, Audio, 8, 3, Subtitle, 1"

To set the player to RCE proof region free
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, 1, Subtitle, 4

3. Player will reset and set to "region-free" and "RCE-free" mode

To restore players factory region code
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, 9, Subtitle, 1

3. Player will reset and set to factory region code


and here is a forum whre you can get more information
http://www.avforums.com/forums/showthread.php?s=df1223ea6de85d218b01e9719ddec248&t=368649

This question is one of my most frequent on FixYa.

There is no "region-free" or "region 0" setting for any DVD player/recorder. Only DVD media can be region free. Every single offer to set a player or recorder to region free that I am familiar with has been a scam. The reason for this is to prevent DVD piracy.

Most DVD players and recorders (SONY included) have provisions for making a maximum of THREE changes to their region code. A fourth attempt at changing the region code will result in the player/recorder being turned into a paperweight.

Bkhopkins- in your case, you will be able to change your region code from region 1 (USA) to region 4 (AUS). Doing so will leave your player with 2 more changes, maximum. Check your manual for the procedure and the exact number of changes you are allowed. Please be aware that after you change to Region 4, any Region 1 DVD's will not be viewable unless you switch back, which will use another of your three changes.

You have an alternative to salvage your DVD's by downloading a program called DVD Shrink. This program is capable of removing the region code from your DVDs and saving them as region-free at the sacrifice of some quality. You will at least the be able to view your US DVD's without sacrificing a region code change on your player.

Good Luck, and Thank You for using FixYa!

Hi,
Do the following step to make your DVD player region free..

1.Turn machine on without disc inside
2.Press menu button
3.Enter region code (See below for list)
4.A highlighted 'region area number' will appear in the upper left corner (some players)
5.Press 9 to change the region number to multi-regional
6.Turn DVD off (remove power from mains)

next time when u power on the DVD ,it will be region free.

region 1 - 29334
2 - 38767 or, 5 7 5 3 8
3 - 56732
4 - 76884
5 - 53814
6 - 24462
ok

Please get the code here : www.regionfreedvd.net/ www.dvdripper.org/dvd-region-codes-vs-ntscpal/ www.regionfreedvd.net/players.html
www.dvdreviewer.co.uk/Forums/...region_code/page1
Best Regards, Jay__bg78u

Hi,
Please follow the steps : To change the player region code
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, * requested region code here (1-8) *, Subtitle, 1

3. Player will reset and requested region code will be set.
- For example to set region code to 3 press: "Enter, 6, >=10, <<, 00F2, Audio, 8, 3, Subtitle, 1"

To set the player to RCE proof region free
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, 1, Subtitle, 4

3. Player will reset and set to "region-free" and "RCE-free" mode

To restore players factory region code
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, 9, Subtitle, 1

3. Player will reset and set to factory region code
Regards, Jay__uji8

Try one of these:

1) Press 'setup' on remote control
2) Move down to the 'lock' picture
3) Press '0000000'
4) Select region code as '0'

Or

1) Power on player with no disc in tray
2) Press PAUSE
3) Key in 314159
5) For multi-region, select 0
6) Press PAUSE again
7) Power off player
8) Wait a minute turn it on.

Howdy,

I just tried this on LGV774W and it worked :))

To make this player region free (or change the region), do the following:

* Ensure that there is no disc in the player (ie: "no disc" is displayed).
* Press PAUSE
* Enter 314159
* Enter the region code (0 for region free, or 1-6).
* Press PAUSE
* Turn the player off for a few seconds.
* Turn the player back on
* Voila! You beauty!!

Alright, just follow these steps and let me know if you have any problems or questions

1. Power and switch on the Durabrand DVD player.
2. Open the DVD disc tray tray or lid.
3. Press Stop.
4. Press 3 - 5 - 9 - 7 (3597 in sequence). Can be done on remote control.
5. Hidden DVD Region menu appears. Select region 0 or 9 using up or down button on remote control
6. Press OK.
7. Close the disc tray and press Standby on the DVD player front