I need to no how to set the time on my watch - Casio ILLUMINATOR DUAL TIME MEN WATCH Watch for Men

To set the time on a Terner Sport watch R1005M, you'll typically need to:Press and hold the "Mode" or "Set" button until the watch enters the time-setting mode.Use the "Start" and "Stop" buttons to adjust the hours and minutes.Press the "Mode" or "Set" button again to save your settings.Please note that the specific steps might vary depending on the exact model of the watch, so it's a good idea to refer to the manufacturer's instructions provided with the watch for precise guidance.

1. Check the battery: Before attempting to set up your watch, make sure that the battery has not run down. If the battery is dead, you will need to have it replaced by a professional watchmaker or authorized Breitling service center.
2. Wind the watch: If the battery is not dead, you may need to wind the watch to get it started. Most Breitling watches have a self-winding mechanism, but if it has not been worn for a long time, it may need to be manually wound.
3. Set the time: Once the watch is running, you can set the time by pulling out the crown (the knob on the side of the watch) and turning it until the hands are set to the correct time. Push the crown back in when the time is set.
4. Set the date: If your watch has a date function, you can set the date by pulling the crown out to the second position and turning it until the date changes. Push the crown back in when the date is set.
5. Synchronize the time: If your watch has a chronograph function (stopwatch), you may need to synchronize the time to ensure that it is accurate. You can do this by starting the chronograph and waiting for it to complete a full revolution.

To set the time on a Dakota one button watch, you will need to follow the instructions in the user manual that came with the watch. If you do not have the user manual, you can try the following steps:

1. Press and hold the button on the top right side of the watch: Press and hold the button until the time display appears.
2. Set the time: Use the button to set the time. The specific sequence for setting the time will depend on the make and model of your watch.
3. Exit the time setting mode: Once the time is set, you will need to exit the time setting mode. The specific steps for exiting the time setting mode will depend on the make and model of your watch.

It is important to note that the steps for setting the time on a Dakota one button watch may vary depending on the specific make and model of the watch. If you are unable to set the time using the steps above, it is recommended to refer to the user manual or contact Dakota customer support for assistance.
If you have a "his and hers" set of Dakota watches, the steps for setting the time on both watches should be the same. You can use the steps above to set the time on both watches.

Thank you for contacting FixYa.

Set Digital Watch
1. Press and hold the "Mode" button on the right side of your Arnette digital watch for three seconds to change the watch's mode. Press and hold the "Mode" button repeatedly until flashing digits indicate that you have entered the watch's time-setting screen.
2. Use the top and bottom buttons on the left side of your Arnette digital watch to increase and decrease number values as desired.
3. Press and hold the "Mode" button repeatedly to exit the time-setting screen and return the watch to time-telling mode.
Set Analog Watch
4. Pull out the watch crown on the right side of your Arnette analog watch.
5. Turn the watch crown clockwise to adjust the hands of your Arnette analog watch to the appropriate time.
6. Push the watch crown back in when you are finished setting the time on your Arnette analog watch.

Best regards. Jewel

this watch needs to be taken in as this is not proper time telling. has the johnson rod been used yet. if not, do so. if so have it taken in and checked with a caver device.

I need to correct the time/date setting on a tozai digital watch.

Press mode til you get to time then press and hold set. Once the hour starts blinking press the ST/SP button to set the time, then press set again for the minutes and do the same thing again. This should let you set your watch.

I found this document to help me. It is from Armitron. My watch didn't look exactly like the one shown, but the instructions still worked.

http://armitron.com/WatchPDFS/ArmitronLadiesDigital.pdf

With the watch in time mode, press and hold the mode button for 4 to 5 seconds until it beeps and the digits start to blink. Then press the mode button again to advance through each setting. When finished press and hold the mode button to exit the setting mode.

Normal 0 MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} Armitron says if the model is not listed on their site call them 718-784-0700. I did and they promptly e-mailed me PDF.file instructions for my M516 watch. - David